background image

1

www.bindicator.com

LAR180212 Rev. E

I. HANDLING AND STORAGE

SAVE THESE INSTRUCTIONS

INSPECTION AND HANDLING

Do not dispose of the carton or packing materials.

Each package should be inspected upon receipt for damage that may have occurred due to mishandling during 
shipping. If the unit is received damaged, notify the carrier or the factory for instructions. Failure to do so may 
void your warranty. If you have any problems or questions, consult the manufacturer Customer Support at 
800-778-9242.

DISPOSAL AND RECYCLING

This product can be recycled by specialized companies and must not be disposed of in a municipal collection 
site. If you do not have the means to dispose of properly, please contact the manufacturer for return and 
disposal instructions or options.

STORAGE

If the Roto-Bin-Dicator

®

 is not scheduled for immediate installation following delivery, the following steps should 

be observed:

1.   Following inspection, repackage the unit into its original packaging.

2.   Select a clean dry site, free of vibration, shock and impact hazards.

3.   If storage will be extended longer than 30 days, the unit must be stored at temperatures between 32° and 

158° F (0° and 70° C) in non-condensing atmosphere with humidity less than 85%.

CAUTION: DO NOT STORE A NON-POWERED UNIT OUTDOORS FOR A PROLONGED PERIOD.

Roto-Bin-Dicator

®

 

Single & Double Switch Models

StockCheck.com

Summary of Contents for Roto-Bin-Dicator

















Reviews: