Part No. 890311 Form No. F010396C
Page 12 of 12
Qty.
Part No.
Description
Item
No.
KD505SPQ
Parts List
continued from
page 11.
19
19
19
19
19
86
WHEEL WITH SPROCKET ASS’Y CAST (21, 94, 95, 96)
900512
2
87
CHAIN 52 PITCH
890239
2
88
CHAIN 40 PITCH
900323
1
89
WASHER FLAT 5/16 (3/8 ID x 7/8 x 1/16)
*8171003
4
90
BOLT CARRIAGE 5/16 -18 x 3/4
*8024039
4
91
WASHER SPRING LOCK 5/16
*8177011
4
92
NUT REGULAR 5/16-18
*8142002
4
93
JACKSHAFT
900320
1
94
SPROCKET (PER ASSEMBLY) 26 TEETH (Size 65A26)
890238
1
95
SCREW SELF TAP 1/4-14 x 3/4 (PER ASSEMBLY)
800505
5
96
WASHER LOCK EXTERNAL TOOTH (PER ASSEMBLY)
*8181007
5
97
JACKSHAFT ASS’Y
(INCLUDE. 93, 101, 102, 107, 108, 109)
890197
1
98
99
LABEL CLUTCH
830503
1
100
LABEL-DANGER GUARDS
900327
1
101
BEARING PLATE
900317
2
102
BEARING BALL (WITH SNAP RING)
900321
2
103
WASHER LOCK 1/4
*8177010
4
104
ROD BAIL CLUTCH
900970
1
105
BAR BRACE HANDLE
900768
1
106
SCREW CAP 5/16-18 x 3/4
*8041026
1
107
SPROCKET - 17 TOOTH
900303
1
108
SPROCKET - 8 TOOTH
900302
2
109
ROLL PIN 3/16 DIA. x 1 1/4 LG.
*8195166
4
110
LOCKNUT 5/16 - 18 FLANGE
850164
5
112
BRACKET CONTROL ASS’Y (INCL. 113, 114, 115)
900221
1
113
SPRING
900136
1
114
ROLL PIN 1/8” DIA. x 1 1/4 LG.
*9195106
1
115
ROD CLUTCH
900208
1
116
SCREW CAP 1/4-20 x 1/2” LG.
*8041002
3
117
WASHER 1/4” FLAT (5/16 ID x 3/4 OD x 1/16)
*8171002
8
118
GUARD CHAIN ASS’Y
890231
1
119
CLIP-CLUTCH CABLE
900999
1
120
121
CLUTCH DOUBLE RELEASE
900307
1
122
WASHER FENDER 5/16
*8172020
1
123
LABEL READ OWNER'S MANUAL
890301
1
* Denotes
standard
hardware item
that may be
purchased
locally.
Solution
Solution
Solution
Solution
Solution
Problem
Problem
Problem
Problem
Problem
Possible Cause
Possible Cause
Possible Cause
Possible Cause
Possible Cause
TR
TR
TR
TR
TROUBLESHOO
OUBLESHOO
OUBLESHOO
OUBLESHOO
OUBLESHOOTING
TING
TING
TING
TING
Before Requesting Service Review These Suggestions
Will not vacuum or has poor
vacuum performance.
Clean debris bag. Shake bag clean or wash. Adjust nozzle height.
Check for hose kit cap. Unclog nozzle or exhaust (see page 5).
Allow air to feed with debris.
Dirty debris bag. Nozzle height set too high or too low. Hose kit cap
missing. Clogged nozzle or exhaust. Excessive quantity of debris.
Engine will not start.
Self propelled drive will not
release .
Clutch cable out of adjustment. Clutch not lubricated and is locked-up.
No self propelling.
Operator's bail not releasing clutch. Broken or out of adjustment
clutch cable. Worn or broken clutch assembly. Bracket control
assembly (item 112) out of adjustment.
Throttle in off position. Out of gasoline. Bad or old gasoline.
Spark Plug wire disconnected. Dirty air cleaner.
Abnormal vibration.
Loose or out of balance impeller or loose engine.
Check impeller and replace if required. Check Engine.
Engine is locked, will not
pull over.
Debris locked inside impeller. Engine problem.
See page 5, Contact an engine servicing dealer for engine problems.
Check stop switches, throttle, and gasoline. Connect spark plug wire.
Clean or replace air cleaner. Or contact a qualified service person.
Adjust clutch cable. See page 9 Clutch Adjustment. Oil clutch.
Adjust clutch cable. Adjust bracket control assembly. Replace any
worn or damaged or malfunctioning parts.
20
20
20
20
20
22
22
22
22
22
BILLY GOAT INDUSTRIES INC.
P.O. BOX 308 (1803 S JEFFERSON LEE'S SUMMIT, MO 64063 / USA
PHONE: 816-524-9666 FAX: 816-524-6983
R
WARRANTY PROCEDURE
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
Note: To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
Purchased
from
Purchase
Date
21
21
21
21
21
Serial Plate
R
ecord your machine model, serial number
and date-of-purchase and where purchased
R
min
-1
Operator
1803 S. Jefferson
P.O. Box 308
Lee's Summit,
MO 64063 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Model
Serial No.
Unit(Weight)
Engine Power
lbs.
kg
kW
rpm
L
A
p
108
95
L
A
Engine Service and Warranty
22.1
22.1
22.1
22.1
22.1
Contact your nearest engine manufacturer's autho-
rized servicing dealer.
