Billion BiPAC 7401VGP Page 112 User Manual Download

Page: 112 / 121

VoIP/(802.11g) ADSL2+ Router

Chapter 4: Configuration

SNMP Version: SNMPv2c and SNMPv3

SNMPv2c is the combination of the enhanced protocol features of SNMPv2 without the SNMPv2
security. The "c" comes from the fact that SNMPv2c uses the SNMPv1 community string paradigm for
"security", but is widely accepted as the SNMPv2 standard.

SNMPv3 is a strong authentication mechanism, authorization with fine granularity for remote monitoring.

Traps supported: Cold Start, Authentication Failure.

The following MIBs are supported:

From RFC 1213 (MIB-II):

System

group

Interfaces

group

Address

Translation

group

ICMP

group

TCP

group

UDP

group

EGP (not applicable)

Transmission

SNMP

group

From RFC1650 (EtherLike-MIB):

dot3Stats

From RFC 1493 (Bridge MIB):

dot1dBase

group

dot1dTp

group

dot1dStp group (if configured as spanning tree)

From RFC 1471 (PPP/LCP MIB):

pppLink

group

pppLqr group (not applicable)

111

Summary of Contents for BiPAC 7401VGP


























































































































Search results

Summary of Contents for BiPAC 7401VGP

Reviews:

Related manuals for BiPAC 7401VGP

Brands by name

Popular brands

Billion BiPAC 7401VGP, User Manual

Search results

Summary of Contents for BiPAC 7401VGP

Reviews:

Related manuals for BiPAC 7401VGP

Brands by name

Popular brands