Billion BiPAC 7401VGP Page 114 User Manual Download | Manualshive

Page: 114 / 121

background image

VoIP/(802.11g) ADSL2+ Router

Chapter 4: Configuration

IGMP

IGMP, known as

Internet Group Management Protocol

, is used to management hosts from multicast

group.

IGMP Forwarding:

Accepting multicast packet. Default is set to

Enable.

IGMP Snooping:

Allowing switched Ethernet to check and make correct forwarding decisions. Default

is set to

Disable.

VLAN Bridge

This section allows you to create VLAN group and specify the member.

Edit:

Edit your member ports in selected VLAN group.

Create VLAN:

To create another VLAN group.

Advanced VLAN Setup Example (Triply Play)

VLAN_data:

Ethernet Port 1, Wireless and Wireless WDS are reserving for Internet
- On Ethernet port 1 I also need VC 0/40 bridged.

VLAN_Vedio

Ethernet ports: 2, 3 and 4:
- 0/33 Bi-directional IP
- 0/34 Video
- 0/35 Video
- 0/36 Video Subscriber Services (EPG, EAS, etc.)
- 0/37 Video
- 0/38 Video
- 0/39 Spare

Step 1: Setup Member Ports

Go to

Configuration

LAN

Bridge Interface.

You can setup member ports for each VLAN group under Bridge Interface section. From the example,
two VLAN groups need to be created.
Ethernet: P1 (Port 1)
Ethernet1: P2, P3 and P4 (Port 2, 3, 4) Please uncheck P2, P3, P4 from Ethernet VLAN Port first.

113

«
...
112
113
114
115
116
...
»

Summary of Contents for BiPAC 7401VGP


























































































































Reviews:

No comments

Related manuals for BiPAC 7401VGP

Brand: D-Link Pages: 2

DES-3526 - Switch - Stackable

Brand: D-Link Pages: 258

LightSpeed Appliance QLS250

Brand: Quantum Pages: 12

Brand: NetComm Pages: 3

AirStation WHR-G300N

Brand: Hornington Pages: 6

Brand: APARIAN Pages: 2

SmartNode 4520 Series

Brand: Patton electronics Pages: 90

LinkStation Mini

Brand: Buffalo Pages: 71

Brand: TRENDnet Pages: 10

JetFusion 2100 Series

Brand: Paradyne Pages: 296

Slideaway CL1008

Brand: ATEN Pages: 77

Brand: Hama Pages: 24

Brand: ZyXEL Communications Pages: 12

Home Base F5L049ea

Brand: Belkin Pages: 59

Brand: MicroNet Pages: 49

Brand: Comelit Pages: 140

TigerSwitch 100 SMC6924VF

Brand: SMC Networks Pages: 174

Brand: Linksys Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands