background image

FCC Notices 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation. 
This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by turning 
the equipment off and on, the user is encouraged to try to correct the interference by one or 
more of the following measures: 
--Reorient or relocate the receiving antenna. 
--Increase the separation between the equipment and receiver. 
--Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected. 
--Consult the dealer or an experienced radio/TV technician for help. 

CAUTION: 

Any changes or modifications not expressly approved by the grantee of this device could void 
the user's authority to operate the equipment. 

RF exposure warning: 

The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. 
The equipment must not be co-located or operating in conjunction with any other antenna or 
transmitter. 

Summary of Contents for BK-T1









Reviews: