background image

Big Woods Hearth Products, Inc. 

  The Hearthwarmer-II Woodburning Insert   5

Warranty

From the date of purchase, The Hearthwarmer-II has a 
full warranty of:

1 - Year Warranty on all the electrical components
3 - Year Warranty on the steel tubing.
      Bar grate is not covered. 

The unit must be installed and operated in accordance 
with the manufacturer’s instructions or the warranty will 
be voided. Damage due to shipping, mis-use or abuse 
is not covered. Damage due to failure to run the blower 
during operation will void the warranty.

The shipping cost to return the unit is not covered. 

1. Fire

Set logs and/or kindling on The Hearthwarmer-II and light  
as normal.  Due to oils used in the manufacturing process, 
there will be some smoke and odor produced on the        ini-
tial fi re.  This is normal and will dissipate with use.  Placing a 
moist towel over the outlet grille (left side of the front grille) 
will help diffuse any smoke that may come into the room. 

2. Blower

The blower is thermostatically controlled and will turn itself 
on as the heat exchanger warms up. The blower speed 
can be regulated using the rheostat knob located on the 
right side of the front grille. BLOWER MUST by running when-
ever the appliance is burning. Failure to run the blower 
during operation will void the warranty. 
Air fl ow and hum-
ming noises are normal during blower operation. As the 
fi re dies down and heat exchanger cools, the blower will 
automatically shut itself off. 

3. Ash Removal

When the fi re has cooled down, periodic ash removal from 
the fi rebox is necessary to maintain optimum use and ef-
fectiveness.  

NOTE: NEVER attempt to remove ashes unless there 

is no fi re present and embers are completely cool! 

4. Bar Grate

The bar grate serves a dual purpose as a log holder and 
providing protection to the heat exchanger tubes. The 
bar grate will need to be replaced over a period of time, 
depending on rate of individual usage. Bar grate replace-
ment is critical for the protection of the heat exchanger 
tubes. The bar grate should never touch the heat exchang-
er tubes.
 When the grate bar deteriorates to the point it is 
nearly touching the heat exchanger tubes, the bar grate 
must be replaced. Failure to do so will damage the heat 
exchanger tubes and void the warranty. 

5. Glass Doors and Ef

fi

 ciency

For maximum heating effi ciency, close the fi replace glass 
doors after the fi res have ended.  Avoid building too large 
a  fi re as the heat may cause discoloration to your glass 
doors and may damage the heat tubing (voiding the war-
ranty). 

The Hearthwarmer-II Operating Instructions

Big Woods Hearth Products, Inc. 

14450 West Burnsville Parkway

Burnsville, MN 55306

P) 952-224-4072

F) 952-224-4074

[email protected]

www.bigwoodshearth.com

Check out our website at 

www.bigwoodshearth.com 

for new products, 

accessories and updates! 

Summary of Contents for The Hearthwarmer-II Woodburning Insert







Reviews: