Big Backyard BALMORAL A24655E Installation And Operating Instructions Manual Download

Page: 26 / 40

Step 13: Chalk Wall Assembly cont.

Place the Chalk Wall Tarp in between (BR13) Back Roof Support and (F10) Top Front Back and (F5) Cedar

Wall. (fig. 13.3)

Attach Chalk Wall Tarp to (F10) Top Front Back, (BR4) Panel Frame, (F5) Cedar Wall and (BR13) Back

Roof Support using 12 (S5) #8 x 1/2” Pan Screws (with #8 flat washer) as shown in fig. 13.3 and 13.4. The 2
screws on (BR13) Back Roof Support are attached from the inside of the assembly.

Tighten the bolts in (BR13) Back Roof Support.

Make sure (F5) Cedar Wall is square and then attach to (BR13) Back Roof Support from the inside of the

assembly with 2 (S1) #8 x 1-1/8” Wood Screws. (fig. 13.4)

From the outside of the assembly and 8” from the inside edge of (BR13) Back Roof Support attach 1 (F18)

Lower Back Wall to (F10) Top Front Back and (F5) Cedar Wall with 4 (S1) #8 x 1-1/8” Wood Screws. (fig. 13.3
& 13.4)

Inside view

Outside view

x 10

Flush

Tighten bolt

Fig. 13.3

Fig. 13.4

Hardware

12 x

#8 x 1/2” Pan Screw (with #8 flat washer)

6 x

#8 x 1-1/8” Wood Screw

Other Parts

1 x Chalk Wall

F10

F18

F10

F18

F13

BR13

1 x

Lower Back Wall 1 x 4 x 31-1/2”

F18

Wood Parts

BR4

BR13

8”

Summary of Contents for BALMORAL A24655E









































Search results

Summary of Contents for BALMORAL A24655E

Reviews:

Related manuals for BALMORAL A24655E

Brands by name

Popular brands

Big Backyard BALMORAL A24655E, Installation And Operating Instructions Manual

Search results

Summary of Contents for BALMORAL A24655E

Reviews:

Related manuals for BALMORAL A24655E

Brands by name

Popular brands