background image

A

Installation, Operation and Maintenance Manual 

MAN 608 Rev. 5

December 2020

Installation

7

Section 2: Installation

Figure 7 

Fixing positions

Position

 1

Standard application

Position

 2

Standard application

Position

 3

Change the position of suction 

pipe from A to B and the 

breather cap to top side

Invert the position of the breather cap

OMFB manual handpump should be transported and used with MHP tank in 
horizontal position, but in position 3 of follow picture (extracted from OMFB technical 
documentation) it’s necessary change the position of suction pipe and breather cap.

2.3 

Storage

If the actuator needs storage, before installation follow these steps:

• 

Place it on a wood surface in order not to deteriorate the area of valve coupling.

• 

Make sure that plastic plugs are present on the pneumatic and electrical 

connections (if present).

• 

Check that the cover of the control group and of the limit switch box (if any) are 

properly closed.

If the storage is long-term or outdoor:

• 

Keep the actuator protected from direct weather conditions.

• 

Replace plastic plugs of pneumatic and electrical connections (if any) with metal 

plugs that guarantee perfect tightness.

• 

Coat with oil, grease or protection disc, the valve coupling area.

• 

Periodically operate the actuator (Section 3.3).

Summary of Contents for OLGAS





















































Reviews: