manualshive.com logo in svg

Bicom Systems OfficeBox, Installation Manual, Page: 22 / 25

Share
Download
Bicom Systems OfficeBox Installation Manual Download Page 22

Figure 24. Connecting officeBOX to electric power

After you have connected the appliance to the electricity you can turn it on by pressing the
On/Off button which can be seen on Figure 1. Also, if you press the On/Off button when the
appliance is working it will shut down immediately.

Software Setup

After officeBOX has been placed, it is time to set it up using the web-based setup wizard. The
manual on how to do this and other related information can be obtained at:

http://www.bicomsystems.com/support/

PBXware image flashing procedure

This step by step guide will help you install PBXware on the appliance. To complete it, you need
to have a Windows PC and a USB memory stick. Also, you must connect a monitor and a
keyboard to the appliance.

Writing image to USB stick

Step 1. Download PBXware image from

■

http://downloads.bicomsystems.com/officebox/pbxware.img

Step 2. Download Image Writer from http://downloads.bicomsystems.com/cw/

■

Step 3. Install the Image Writer

■

Summary of Contents for OfficeBox


























Reviews:

No comments