Biamp Audia EXPI, Operation Manual

Page: 5 / 20

3
Audia EXPO - Front & Rear Panels
BIAMP
SYSTEMS
1 2 3 4 5 6 7 8
Levels (Outputs 1~8) : These screw-driver adjustable controls set the channel output gain (-95dB ~ 0dB) to provide appropriate signal
levels to any subsequent audio equipment.
Rotary Encoder & LCD Display:
This control and display are used for initial setup of the Audia EXPI unit. When power is first applied to
the unit, the display will cycle through a product description, followed by a title screen. Press the control to enter setup. Rotate the control
to make a selection, then press the control again to edit that selection. Additional levels of selection may be available using this same
routine. Some edits will require a choice of 'OK' or 'CANCEL. Some selections are only informational, and cannot be edited. Select
'BACK' to return to a previous level, and select '
→
' to advance. Primary selections are as follows: BUNDLE NUMBER (CobraNet bundle
number to logic input assignments); COBRANET LATENCY (dependent upon CobraNet firmware); PASSWORD PROTECT (prohibits
unauthorized tampering); TITLE DISPLAY (personalized: 2 lines with 8 characters each); ABOUT (serial#, version#, and Ethernet address
information).
25 watts
class 2 wiring
50/60 Hz
~
27V
8 logic inputs 7 6 5 4 3 2 1
line outputs
CobraNet TM connections only
secondary
U.S. pat. no. 4,922,536
green: in use
green: link/act
orange: conductor
red: fault
LEDs
primary
1 2 3 4 5 6 7 8
MADE IN U.S.A.
BIAMP SYSTEMS
Portland, Oregon
an affiliate of Rauland-Borg Corp.
8 out
Line Outputs: These eight line-level analog audio outputs are provided on balanced plug-in barrier-strip connectors. For unbalanced
output, wire high to (+) and ground to (
d
), leaving (-) un-connected.
Logic Inputs:
These eight Logic Inputs allow remote control of CobraNet bundle number assignment (see CobraNet below). Bundle
numbers can be assigned to Logic Inputs using the front panel Rotary Encoder (see above), and can then be selected via external contact-
closures (wired from the corresponding logic inputs to ground). Bundle numbers are used to route digital audio signals to specific devices
in a system network.
CobraNet: These two RJ45 connectors provide the CobraNet digital audio interface. CobraNet allows multiple AUDIA units to share
digital audio (and DSP resources) on a system network. This also allows AUDIA units to be used with CobraNet compliant devices from
other manufacturers. A 10/100Base-T Ethernet switch (not hub) is required when networking multiple units. The maximum distance
between any unit and an Ethernet switch is 100 meters. Additional Ethernet switches, or even fiber-optics, can be used to further extend
distances between units on a system network. The primary and secondary CobraNet ports are redundant. CobraNet supports 64
channels of digital audio (32-in & 32-out) over Fast Ethernet, using CAT-5 cable. CobraNet transmits (32) channels of digital audio on (4)
'bundles' of (8) channels each. The same is true for receiving digital audio over CobraNet. Bundle numbers are used to determine where
digital audio is transmitted and received. Typically, 'unicast' bundle numbers (256~61,439) are used to exchange digital audio between two
specific devices. With 'unicast' bundles, each CobraNet device can transmit to no more than (4) other devices within a network. With
'multicast' bundle numbers (1~255), digital audio can be exchanged with multiple devices. Due to network delay, CobraNet has a limitation
of seven (7) 'hops' (one-way transmissions) within a network.
In order to integrate Audia
EXPO into a AUDIA system, an EXPO (or CobraNet) output block must first be placed into the design layout.
AUDIA units intended to transmit digital audio to the Audia EXPO must have their CobraNet jacks connected to the same network. Both the
Audia EXPO unit (hardware) and the EXPO output block (software) must be assigned matching bundle numbers, before digital audio can
be successfully exchanged. Audia EXPO bundle number assignment can be changed in real-time to allow access to digital audio from
different EXPO output blocks within the system. CobraNet Latency settings must be identical in all devices, system-wide. Also, unicast
and multicast bundle numbers can be used to access digital audio from individual or multiple EXPO output blocks. Similar considerations
may apply when using Audia
EXPO with other CobraNet compliant systems or devices. Audia EXPI and Audia EXPO can exchange digital
audio directly (outside of a system network) using either a simple 'cross-over' CAT5 cable or an Ethernet switch.