background image

Supertop for Truck Installation Instructions

Rev. G 0713

76303 pg. 3

Mount Tailgate Brackets to 
Rear Belt Rails

Assemble Retainer Bar

Locate the Bow Mount Brackets in the parts kit.  Slide a 5/16" Flat Washer 

over a 5/16" x 3/4" Clevis Pin. Insert the pin through the rear pivot hole on the 

Bow Mount Bracket from the outside.
Slide a 1/4" Fender Washer over a 1/4" x 1-1/2" Clevis Pin and insert the pin 

through the front slot of the Bow Mount Bracket from the outside.
Repeat this with both Bow Mount Brackets.

Assemble Bow Mounts Brackets

Locate the Right Front and Rear Belt Rails. Place the ends of the rails against 

each other. Place the Right Bow Mount Bracket on top of the Belt Rails. Secure 

the bracket to the rails with four (4) 1/4-20 Cap Nuts 1/4" Flat Washers.
Repeat this with the Left Side Bow Mount Bracket and Belt Rails.

Assemble Main Bow Mount Brackets 
and Belt Rails 

Right Rear Belt Rail

Right Tailgate Bracket

1/4-20 Cap Nut

Bow Mount Bracket

Rear Pivot 

Hole

Front Slot

5/16" Flat Washer 

5/16" x 3/4" Clevis Pin

1/4" x 1-1/2" 

Clevis Pin

1/4" Fender Washer

Bow Mount 

Bracket

Rear Belt Rail

Front Belt Rail

1/4-20 Cap Nuts

Locate the Right Tailgate Bracket and the Right 

Rear Belt Rail in the parts kit. Place the Right Tail-

gate Bracket  over the rear stud on the Belt Rail so 

that the bracket tab points away from the channel 

on the Belt Rail. Use a 1/4-20 Cap Nut and 1/4" Flat 

Washer to secure the bracket to the rail.
Repeat with the Left Tailgate Bracket and Rear Belt 

Rail.

1/4" Flat 

Washer

Locate a Front Retainer Bar Bracket and the Right 

Front Belt Rail. Place the bracket over the front stud 

which is the one that is 1 1/2" from the front of the 

rail. Use a 1/4"-20 Cap Nut and 1/4" Flat Washer to 

secure the bracket to the rail. 
Repeat with the Left Front Belt Rail. 

Mount Front Retainer Brackets to Front 
Belt Rails

Right Front 

Belt Rail

Front Retainer 

Bar Bracket

1/4"-20 

Cap Nut

1/4" Flat 

Washer

1/4" Flat Washers

Assemble the two Retainer Bar halves by sliding the 

inner half into the outer half and align the pre-drilled 

holes. Install a #8 X 1/2” Self Drilling screw in to the 

pre-drilled hole.

Summary of Contents for 76303














Reviews: