manualshive.com logo in svg

Best Power B510-0600A, Installation And Operation Manual, Page: 43 / 50

Share
Download
Best Power B510-0600A Installation And Operation Manual Download Page 43

BEST 510

ADVANCED COMMUNICATIONS

COMMUNICATION PROTOCOL

STATUS ENQUIRY:

Computer:

Q1<cr>

UPS:

UPS status data stream, such as

(MMM.M NNN.N PPP.P QQQ RR.R S.SS TT.T b7b6b5b4b3b2b2b0<cr>

UPS status data stream:

(a)

Start byte

(

(b)

Input Voltage:

MMM.M

M is an integer number ranging from 0 to 9. The unit is volts.

(c)

Input Fault Voltage:

NNN.N

N is an integer number ranging from 0 to 9. Its purpose is to identify a

short duration voltage glitch that causes UPS to go to inverter mode. If this

occurs, input voltage will appear normal at query before glitch and will still

appear normal at next query.

The I/P fault voltage will hold the glitch voltage until next query. After the

query, the fault voltage will be same as voltage until next glitch occurs.

(d)

Output Voltage:

PPP.P

P is an integer number ranging from 0 to 9. The unit is volts.

(e)

Output Current:

QQQ

QQQ is an integer percent of maximum current, not an absolute value.

(f)

Input Frequency:

RR.R

R is an integer number ranging from 0 to 9. The unit is Hz.

(g)

Battery Voltage:

SS.S or S.SS

Actual battery voltage is provided in the form SS.S. The unit is volts.

(h)

Temperature:

TT.T

T is an integer number ranging from 0 to 9. The unit is degrees centigrade.

Appendix A

 26

Summary of Contents for B510-0600A



















































Reviews:

No comments