manualshive.com logo in svg

Best Power B510-0600A, Installation And Operation Manual, Page: 31 / 50

Share
Download
Best Power B510-0600A Installation And Operation Manual Download Page 31

BEST 510

•

Pins 2, 3 and 5 are all driven by open collector transistors. Pull up
resistors are required on the host computer side.

•

Pin 2 is closed and Pin 3 is open when the utility is unavailable.

•

When the battery backup time is less than 2 minutes, Pin 5 is
closed.

•

In any condition, shorting Pin 8 with Pin 4 for 0.5 seconds will turn
off the UPS.

•

Keeping Pin 6 in RS-232 high level (5-12V) for 0.5 seconds will
shut down the UPS. The UPS automatically “wakes up” when the
utility comes back. This shutdown function only operates in battery
mode.

•

Pin 6 , Pin 7 and Pin 9 are for the RS-232 serial interface.

NOTE

1.

Pins 2, 3 and 5: current 20Vdc, 50mA non-inductive.

2.

Pin 4 should be connected to ground only.

COMMUNICATIONS 

(cont.)

COMMUNICATION PORT

The UPS provides signals and RS-232 interface on a DB9 connector for the
host computer to contol the UPS and obtain the utility status.

The pin assignment for the female DB9 connector is:

Pin 1: NOT USED
Pin 2: LINE FAIL CONTACT (normally open)
Pin 3: LINE FAIL. (normally closed)
Pin 4: COMMON for Pins 2, 3, 5 and 8.
Pin 5: TWO MIN. CONTACT. (normally open)
Pin 6: RS-232 DATA TO UPS (RX)/

SHUTDOWN (high level)

Pin 7: RS-232 COMMON
Pin 8: REMOTE OFF (low level)
Pin 9: RS-232 DATA from UPS (TX).

Communications

14

Summary of Contents for B510-0600A



















































Reviews:

No comments