Best Barns Millcreek Assembly Book Download | Manualshive

Page: 20 / 24

background image

Straight Edge

Metal Truss Hanger

Soffit Board Flush With Siding

To prevent the nails from protruding
thought the bottom of the soffit board,
nail at an angle when nailing roof
sheathing to the soffit boards.

1.

Place trusses over the 'X' marks and secure

trusses to 2x4 truss plate using 2x4 hangers and
10d coated sinker nails.

2.

Locate 65-1/4" long soffit boards that have a

beveled edge. Install one of these boards flush
with the top of the siding and butting against
the rear gable trim. Secure soffit boards to the
top wall plate with 3" long screws spaced 8"
apart. Install the last soffit boards to fit behind
2x3 boards on the front gable.

Step 19

Install Trusses & Soffit Boards

1.

Install a 42" x 72" OSB roof panel flush with

the face of the rear gable trim. Use a straight
edge to align the top of the sheathing with the
top of the truss. Continue adding sheathing
following the layout on the next page. Use
7d coated sinkers, spaced 6" apart.

2.

Repeat step for opposite side.

Step 20A Install Roof Sheathing

«
...
18
19
20
21
22
...
»

Summary of Contents for Millcreek

























Reviews:

No comments

Related manuals for Millcreek

Brand: Palmako Pages: 52

CLA128-SLIDER-METAL-ES

Brand: OLT Pages: 44

Extension LAZA28-1624

Brand: Palmako Pages: 51

Brand: Karibu Pages: 27

Brand: Palmako Pages: 102

Brand: Palmako Pages: 43

Brand: Palmako Pages: 75

Brand: Palmako Pages: 29

Brand: Palmako Pages: 29

Brand: Best Barns Pages: 16

Northwood Deluxe 10x10

Brand: Best Barns Pages: 20

Brand: Best Barns Pages: 20

Brand: Universo Consumer Products Pages: 24

Brand: Vitavia Pages: 32

Brand: OSTO Pages: 17

Brand: Alpha Pages: 22

Brand: Alpha Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands