Best Barns Millcreek Assembly Book Download | Manualshive

Page: 15 / 24

background image

2.

Remove 2x4 wall braces and

cut to fit under second beam..

3.

Repeat to install the other 2x6

beam. Install the beam to the
side of the double studs facing
the back of the building.

.

Double Stud

2x6 Beam

76-1/4" 2x4 Board

1.

Install the front 2x6 beam to the side of the double studs facing the front of the building. Place

the notch under the top plate. Cut to fit under the beam the (2) two 2x4s removed from pallet.
Toenail to beam with 10d sinkers. Further secure the beam with a 2-1/2" wood screws through
the top of the wall plate.

Important: When installed properly the 'X' marks will
be facing the front wall on the front beam and the back
wall on the back beam. The beams will be 51" apart.

Step 13

Install 2x6 Loft Beams

«
...
13
14
15
16
17
...
»

Summary of Contents for Millcreek

























Reviews:

No comments

Related manuals for Millcreek

Brand: Palmako Pages: 72

CLA128-SLIDER-METAL-ES

Brand: OLT Pages: 44

Brand: Lillevilla Pages: 40

02PLAY511511-V2-PEFC

Brand: Mercia Garden Products Pages: 9

Brand: Palmako Pages: 54

Brand: Palmako Pages: 56

Brand: Palmako Pages: 56

Brand: Palmako Pages: 27

Brand: Palmako Pages: 30

Brand: Palmako Pages: 44

NORDIC PLUS 15 ED-FLD

Brand: Gartenpro Pages: 45

Brand: Palmako Pages: 101

Brand: Palmako Pages: 21

Brand: Palmako Pages: 60

Brand: Palmako Pages: 25

Brand: habitat et jardin Pages: 29

Brand: habitat et jardin Pages: 12

Brand: Rowlinson Garden Products Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands