10
11
child seat might touch the interior. We recommend using a (BeSafe)
protection cover in these places to avoid cuts, marks or discolouration to
the interior of the vehicle, especially in vehicles with leather or wooden
interiors.
•
If in doubt, consult either the car seat manufacturer or the retailer.
Preparing to install
Installation
1.
When installing in the back seat of the vehicle, push the front seat of the
vehicle forward as far as possible and adjust the back rest into an upright
position (if it can be adjusted).
2.
When installing in the front seat of the vehicle, adjust the back rest into
an upright position.
3.
Position the vehicle on a horizontal surface when installing the seat.
4.
When the base is lifted the floor support should fall downwards from
underneath the base. Do this outside the car.
5.
Push down the switch for the ISOfix connectors at both sides to release
the ISOfix connectors. (2)
6.
Position the base on the vehicle seat. Click the ISOfix connectors on to
the ISOfix anchorages on the vehicle seat. Make sure that both ISOfix
•
Adjustable headrest
•
Shoulder straps
•
Baby insert
•
Baby cushion
•
Harness buckle
•
Central adjuster
•
Reclining handle
•
Release handle headrest
•
Installation screen
•
Spirit level
•
Battery compartment
•
Floor support
•
Floor support height indicator
•
Height adjuster floor support
•
Rotation release handle
•
Switch for ISOfix connectors (2x)
•
ISOfix connectors (2x)
•
ISOfix release switch
•
ISOfix indicators (2x)
•
ISOfix car anchorage (2x)
(1a)
(1b)
(1c)
(1d)
(1e)
(1f)
(1g)
(1h)
(1i)
(1j)
(1k)
(1l)
(1m)
(1n)
(1o)
(1p)
(1q)
(1r)
(1s)
(1t)
indicators are green. (3)
7.
Push the seat towards the backrest of the vehicle seat until it touches the
backrest. (4)
8.
The ISOfix connectors will have resistance sliding in, in the most outward
positions, before they are connected with the ISOfix anchorage of the
vehicle.
9.
Tip: once the ISOfix connectors are installed, the seat can be turned
towards the door of the vehicle to get a better view on the installation
display.
10.
Remove the yellow cap from the floor support. Adjust the floor support, so
it is in contact with the floor of the vehicle. (5)
11.
The height indicator of the floor support shows green when the floor
support is in contact with the floor. (5)
12.
Lift the base at the front side (near the spirit level) and extend the floor
support till the spirit level is in the middle, indicating a horizontal position
of the base. (5)
13.
Tip: place one foot onto the bottom end of the floor support while lifting
the base to make adjusting the length at this step easier.
14.
The alarm sound stops when the floor support indicators show green and
it is in contact with the floor and (not for all models) when the spirit level
shows a horizontal position of the seat. (5)
15.
When having the child seat installed rear facing in the back, it is
recommended to position the front vehicle seat in a way that it is close to
the touchpoint with the child seat. Make sure that the child seat can still
rotate freely.
When having the child seat installed rear facing on the passenger seat in
the front, it is recommended to position the passenger seat in a way that
the dashboard is close to the touchpoint with the child seat. Make sure
that the child seat can still rotate freely.
16.
Tip: If you feel like the base has too much side movement, you can install
the seat tighter against the vehicle seat backrest. Make the support leg
short, grab the base and push it against the vehicle backrest with more
force. Move it side to side until you hear one more ‘click’ per side, then lift
the base into horizontal position again.
17.
The seat is delivered with removable SIP+ (side impact prot).
This extra side impact protection should be used on the doorside of the
vehicle. To connect your SIP+ version, follow the instruction drawings
on the SIP+ included with your seat. The seat already offers high level
integrated side impact protection. This extra side impact protection
improves the protection in the side impact still further. (6)
18.
Tip: For an optimal height of the SIP+, position it between the two raised
dots on the side of the seat shell.
