Berner BBC-2 14,4-18V Manual Download Page 8

Page: 8 / 60

BBC-2

14,4-18V

.......................14,4 V, 18 V

.....................................3 A

.................................500 mA

.................................704 g

..........................+5...+40 °C

ENGLISH

WARNING Read all safety warnings, instructions, illustrations and

speci

cations provided with this power tool.

Failure to follow all instructions

listed below may result in electric shock,

re and/or serious injury.

Save all warnings and instructions for future reference.

SAFETY INSTRUCTIONS

Do not dispose of used battery packs in the household refuse or by burning

them. Your power tool distributor will normally retrieve old batteries to protect

our environment.

Only the following battery packs can be

charged with this charger:

Battery Cat. No.

Cell Type

DC Volts

Capacity

Cell No.

BBP14,4V

Li-Ion

14,4

≤

1,5 Ah

BBP14,4V

Li-Ion

14,4

≤

3,0 Ah

2 x 4

BBP18V

Li-Ion

≤

2,0 Ah

BBP18V

Li-Ion

≤

5,0 Ah

2 x 5

BBP18V

Li-Ion

≤

9,0 Ah

3 x 5

Do not try to charge non-rechargeable

batteries with this charger.

Do not store the battery pack together with metal objects (short circuit risk).
No metal parts must be allowed to enter the battery section of the charger

(short circuit risk).
Never break open battery packs or chargers and store only in dry rooms. Keep

dry at all times.
The battery clamps of the charger are fed by the mains supply. Do not touch

the tool with conducting objects.
Never charge a damaged battery pack. Replace by a new one.
Before use check machine, cable, and plug for any damages or material

fatigue. Repairs should only be carried out by authorised Service Agents.

This appliance is not intended to be used or

cleaned by persons with reduced physical,

sensory or mental capabilities, or lack of

experience or knowledge, unless they have

been given instructions concerning the safe

use of the appliance by a person legally

responsible for their safety. They should be

supervised whilst using the appliance.

Children shall not use, clean or play with this

appliance, which when not in use should be

secured out of their reach.

Warning!

To reduce the risk of

re, personal injury, and product damage due

to a short circuit, never immerse your tool, battery pack or charger in

uid or

al-low a

uid to

ow inside them. Corrosive or conductive

uids, such as

seawater, certain industrial chemicals, and bleach or bleach containing

products, etc., Can cause a short circuit.

SPECIFIED CONDITIONS OF USE

The quick charger can charge Berner Li-ion batteries from 14 V - 18 V.
Do not use this product in any other way as stated for normal use.

MAINS CONNECTION

Connect only to single-phase AC current and only to the system voltage

indicated on the rating plate. It is also possible to connect to sockets without an

earthing contact as the design conforms to safety class II.

CHARGING TIME

Battery Cat. No.

Volts

Capacity

Charging Time

max.

BBP14,4V

14,4 V

≤

1,5 Ah

40 min

BBP14,4V

14,4 V

≤

3,0 Ah

75 min

BBP18V

18 V

≤

2,0 Ah

40 min

BBP18V

18 V

≤

5,0 Ah

75 min

BBP18V

18 V

≤

9,0 Ah

191 min

LI-ION BATTERIES

The rechargeable batteries are partially charged. The LED on the battery

indicates the state of charge.
If it is not used for long periods, the rechargeable battery will switch to the

non-operative state.
When fully discharged the rechargeable battery switches o

ﬀ

automatically

(depth discharge not possible).
Under extreme circumstances, the internal temperature of the battery could

become too high. If this happens, the battery will shut down.
Place the battery on the charger to charge and reset it.
The state of charge can be read by pressing the button on the rechargeable

battery. The battery can be left in the electric tool while the reading is taken but

it must be switched o

ﬀ

at least one minute beforehand (otherwise the display

will be inaccurate). The number of LEDs illuminated indicates the state of

charge. A

ashing LED indicates a max. power reserve of 10%.

As a general principle, if the electric tool should fail to work after inserting the

rechargeable battery, then the battery should be plugged into the charger. The

displays on the battery and charger will then provide information about the

condition of the battery.
In low temperatures work may continue at reduced output.

LI-ION BATTERIES

The rechargeable batteries are partially charged. The LED on the battery

indicates the state of charge.
If it is not used for long periods, the rechargeable battery will switch to the

non-operative state.
When fully discharged the rechargeable battery switches o

ﬀ

automatically

(depth discharge not possible).
Under extreme circumstances, the internal temperature of the battery could

become too high. If this happens, the battery will shut down.
Place the battery on the charger to charge and reset it.
The state of charge can be read by pressing the button on the rechargeable

battery. The battery can be left in the electric tool while the reading is taken but

it must be switched o

ﬀ

at least one minute beforehand (otherwise the display

will be inaccurate). The number of LEDs illuminated indicates the state of

charge. A

ashing LED indicates a max. power reserve of 10%.

As a general principle, if the electric tool should fail to work after inserting the

rechargeable battery, then the battery should be plugged into the charger. The

displays on the battery and charger will then provide information about the

condition of the battery.
In low temperatures work may continue at reduced output.

TRANSPORTING LITHIUM BATTERIES