18
meat, a grinder plate "2", a knife "3" coupled to plate "4", a second knife "5" with a
holed plate "6".
B Assembly "B" , (half unger), a spacer "7" replaces knife “5” and plate “6”
C Normal assembly "A" is the simplest assembly and consists of a worm screw, a
knife and an end plate.
It is not possible to mount the plates for assemblies “B” and “C” on models with
mincing assemblies “A”. The entire assembly group has to be changed.
6.4 How to use the meat mincer—mixer
This machine is designed to mix meat and convey it to the product inlet for mincing.
Load to the meat to be processed into the mixer, the general power switch should be
off - in position “0”. The food product is loaded from above and must remain inside
the hopper. Do not exceed mixer volume capacity. Close the protection grille and
proceed with starting operations (chap. 5). Make sure the paddle rotates in an
anticlockwise direction. Tighten the collar ring slightly “4” (Fig. 6.2.1) on the mincing
outlet and start the mincer. If the meat is minced correctly there is no need to adjust
the collar. If adjustment is necessary tighten the collar “4” slightly until obtaining the
required mincing quality. When all the meat has been minced press the stop button to
stop the mincer. To avoid excessive wear in the plates and knives which not only
saves on parts but ensures better mincing quality, stop the mincer when there is no
meat in the machine. If necessary it is possible to reverse both mixing and mincing
rotation, however remember that to stop mixer reverse rotation you must press the
mixer stop button, whereas for the mincer simply release the reverse button to stop
the mincer automatically.
6.5 Removal and disassembly of tools (Fig.
6.2.1)
- Switch the general power switch to “0” - off.
- Raise the protection grille "1", unhook the four
hinges "5", raise the front panel "3".
- Remove all waste product on the mixing tool
(paddle) "2".
- Remove collar ring "4". This operation does not
require the use of additional tools (just your hands).
- Remove the mincing assembly.
- Unscrew nuts "6" and remove the cylinder "7".
Clean all parts thoroughly (refer to chap. 7.6).
6.6 - Optional
6.6.1 Optional trestle with wheels (A fig.
6.6.1)
Pay attention in moving machine with legs
and wheels.
A
B
Fig. 6.6.1
UM - CODE S31 - REV 0.0
7
1 Delivery and Warranty Terms
1.1 - Foreword
CAUTION!
These symbols have been used to draw the reader’s attention to
hazardous operations and possible machine hazards to guarantee operator and
machine safety. Do not use the machine if you have not understood in full the warnings
provided in this manual.
CAUTION!
Some of the drawings provided in this manual illustrate the machine or its
parts without protective panels or devices in place to provide a clearer and better
understating of the machine components. Do not use the machine without all the
necessary protections and safety devices correctly assembled, efficient and in place.
It is forbidden to reproduce either in full or in part contents of this manual.
Any violation of copyright will be liable to prosecution.
1.2 - Storing and Using this manual
This manual is meant to provide users with information and details about transport,
installation, use and maintenance of the machine. For this purpose, this manual has
been provided with descriptions and drawings. Before using the machine, read this
manual thoroughly. Store this manual with care near the machine in an easily
accessible place to allow for easy reference when required. If the manual is damaged or
lost, ask your local dealer for a new copy or contact the manufacturer directly. In the
event the machine is sold, provide the manufacturer with the new owner’s details: name
and address.
The information and technical specifications provided in this manual correspond to
those at the moment of product marketing and as such cannot be considered
inadequate due to new product improvements or updates. The manufacturer has the
right to alter or modify its products and / or manuals without having to alter previous
models or manuals, except in specific cases.
In case of doubt, contact your local service centre or the manufacturer directly.
Due to ongoing product improvement the manufacturer continuously improves and
modifies the product, therefore any suggestions or ideas that could improve machine
performance or this manual are most welcome.
Warranty terms and conditions are those valid at the time of purchase. If you have any
queries in regard, please contact your local dealer.
1.3 - Warranty Terms
The user shall not tamper, alter or modify the machine in any way for whatever reason.
If a malfunction occurs, contact the manufacturer. Any attempts at dismantling,
modifying or in general tampering with any component of the machine by the user or by
unauthorised personnel shall null and void warranty cover and the Declaration of
Conformity provided conforming to the EEC Directive 89/392, and the manufacturer
shall not be held liable for any injury to persons or damage to things. Furthermore, the
manufacturer shall not be liable for injury to persons or damage to the machine and
property caused by:
- incorrect installation;
- improper use of the machine by unskilled personnel;
- failure to comply with the regulations in force in the country in which the machine is
used;
- lack of or insufficient maintenance;
- use of non-original spare parts and spare parts not specifically designed for the
UM - CODE S31 - REV 0.0
