background image

1 | GENERAL INFORMATION

4

1

GENERAL INFORMATION

1.1

General Notices

When you get the product, check immediately that the contents are
all present and undamaged. Contact the dealer 

if you notice 

any problems.

The product' s installation must be carried out by an authorised
company that will issue a declaration of the installation's conformity
to the product's owner once the work has been completed,
indicating that the work has been carried out in accordance with the
standards of good practice, current National and Local regulations,
and  the  indications  provided  by 

in  the  instruction  booklet 

accompanying the device.

The  product  must  be  used  for  its  intended  purpose,  as  stated  by 

for  which  it  has  been  expressly  manufactured. 

shall 

bear no responsibility, whether of a contractual or non-contractual
nature, for any damage caused to people, animals, or property due
to incorrect installation, adjustments, or maintenance, or improper
use.

Suitable clothing, instrumentation, and accident-prevention devices
must be utilized during the installation and/or maintenance
operations. 

shall  bear  no  responsibility  for  any  failure  to 

comply with current safety and accident-prevention regulations.

During installation and/or service operations, keep the area around
the unit tidy and clean.

Comply with the legislation in force on the country of deployment
with regard to the use and disposal of packaging, of cleaning and
maintenance products and for the management of the unit's
decommissioning.

Any  repair  and  maintenance  interventions  must  be  carried  out  by 

Technical  Support  Service,  in  accordance  with  the 

provisions contained in this publication. Do not modify or tamper
with the unit as dangerous situations may arise and the unit
manufacturer will not be liable for any damage caused.

In the event of any functional anomalies or fluid leaks, set the
system's main switch to its "off" position. Promptly contact your
local 

Technical  Support  Service,  and  do  not  perform  any 

interventions upon the device on your own.

The units contain refrigerant gas: operate carefully so as to avoid
damaging the gas circuit and the fin bank.

Do not place any inflammable object (spray cans) within a 1 metre
radius from the air expulsion.

According to EU Regulation no. 517/2014 regarding certain
fluorinated greenhouse gases, the total amount of refrigerant
contained within the installed system must be indicated. This
information can be found on the unit technical data plate.

This unit contains fluorinated greenhouse gases covered by the
Kyoto protocol. Maintenance and disposal activities must be carried
out exclusively by skilled personnel.

The R32 refrigerant gas is slightly inflammable and odourless.
Carefully read the safety data sheet available from the dealer.

This booklet is an integral part of the device, and must therefore be
carefully preserved, and must ALWAYS accompany it, even in the
event that it is sold to another Owner or User, or is transferred to
another system. If it is damaged or lost, another copy can be
requested to 

Technical Support Service in your Area. 

1.2

Safety precautions

It should be noted that the use of products that utilize electric energy
requires certain essential safety regulations to be respected, including the
following:

Do not allow children or unassisted disabled people to use the unit.

Do not touch the unit while barefoot and/or partially wet.

Do not spray or throw water directly on the unit.

It is forbidden to place weights on the device.

It is strictly forbidden to touch the coil fins, the moving parts, to place
any body parts between them, or to insert pointy objects into the
grilles.

It is forbidden to perform any technical interventions or cleaning
operations before having disconnected the device from its electrical
power supply, by setting the system's main switch to its "OFF"
position.

It is forbidden to modify the safety or regulation devices without the
authorisation of the manufacturer.

Do not pull, detach or twist the electrical wires coming out of the
unit, even when the unit is disconnected from the power grid.

The packing material must not be disposed of in the surrounding
environment and must be kept out of children reach, as it can be
dangerous. It must be disposed of according to the regulations in
force.

Summary of Contents for 20171586

























Reviews: