Berbel BWH 90 GL Operating And Installation Instructions Download

Page: 10 / 32

Installation

6005737_0 – 31.03.2021

3.5

Installation procedure

Short overview:
1.  Preparation for installation
2.  Unpack the device
3.  Removing the lower section and separating unit
4.  Hanging the device in place
5.  Connect accessories
6.  Fitting the BackFlow port
7.  Installing filter (with recirculating and hybrid operation)
8.  Connecting exhaust air ducting (with extracted air and

hybrid mode)

9. Establish electrical power supply
10. Mounting the chimney
11. Inserting lower section and separating unit
12. Check and carry out commissioning

3.5.1

Preparation for installation

☞

Familiarise yourself with the installation situation and the
associated documents.

Device and instructions.

Accessories.

Installation location.

Intended operating mode.

☞

Assemble the tools and materials required:

Stable stepladder

Folding rule or measuring tape

Pencil

Spirit level

Slotted screwdriver SL 2.5 x 0.4

Torx screwdriver TX30

Ø 8 mm masonry bit

Hammer drill

10 mm spanner

Cutter blade

Protective material (e.g. thick cardboard) for the hob
and the worktops

☞

Keep the installation area free of objects that could be in
the way or that could be damaged.

☞

Make sure that the hob and other parts that could be
touched have cooled down.

☞

Protect the hob and other surfaces in the installation area
(e.g. with thick cardboard).

☞

Ensure that the power supply is switched off and remains
so. Connect the power supply only when instructed to do
so in the installation instructions.

If accessories (e.g. wall box, window contact switch) are
required for the installation:

Observe the instructions for the accessories.

☞

Ensure that the accessories are correctly installed and
ready for connection.

☞

Ensure that the connection cables from accessories are
correctly routed and accessible.

3.5.2

Unpack the device

ATTENTION!

Hazard of glass breaking or other damage due to

incorrect handling!

The device and its surfaces can be damaged when being
unpacked or transported.

☞

Do not cut into the protective cardboard packaging.

☞

Keep objects that could scratch the device far away from
it (e.g. tools, belt buckles).

☞

Unpack the device and all accompanying parts carefully.

☞

Place the device on its back on a firm, clean and
protective surface (e.g. thick cardboard).

☞

Check the device and its constituent parts for damage.

☞

Check the delivery is complete.

“2.4 Scope of delivery” (page 7).

If parts are missing or damaged:

☞

Please consult your dealer or customer services.

☞

Remove the packaging material and the protective film.

“8.1 Dispose of packaging” (page 29).

Summary of Contents for BWH 90 GL

































Search results

Summary of Contents for BWH 90 GL

Reviews:

Related manuals for BWH 90 GL

Brands by name

Popular brands

Berbel BWH 90 GL, Operating And Installation Instructions

Search results

Summary of Contents for BWH 90 GL

Reviews:

Related manuals for BWH 90 GL

Brands by name

Popular brands