background image

170 091 16  15-01

3(3)

Cause

Remedy

The burner is operating correctly but locking out now and 
then

The ionisation current is too low

Check. Must be at least 4  µ A according to 
the relay manufacturer but should be 8-20 µ A.

The UV-cell is in a wrong position

Adjust

Voltage drop at certain times

Must not drop more than 15% of the rated 
current. Contact the electricity authorities if 
necessary.

Air pressure switch defective or incorrectly adjusted
Spark-over in ignition electrodes

Replace the electrodes

The ambient temperature of the gas relay is too high

Heat insulate, max. 60° C.

The ignition spark is too weak

Check the transformern

Bad combustion

Bad draught conditions

Check the chimney

The flue gas temperature is too high

The boiler is overloaded. Reduce the 
quantity of gas.

The CO2-content is too low

Check the boiler with regard to leaks. Choke 
the draught  if it is too high.

The CO-content is too high

Excess air when using natural gas and gasoil (propane, butane)

Choke the air.

Air shortage

Open the air supply. Check the flue gas 
damper.

The holes in the gas nozzle are clogged

Clean

The fresh air intake is too small

Check and enlarge.

The flame is not burning straight because the burner head is out of 
position

Check the burner head and readjust.

Condensation in boiler and chimney

The flow gas temperature is too low or the quantity of gas is not 
sufficient

Increase the flue gas temperature by 
increasing the gas supply. Insulate the 
chimney

Summary of Contents for STG 146





























Reviews: