background image

 

1210SHH_AMEN,page 10/29 

 

6.2 

Type B appliances 

 
6.2.1 

Flues for power vented installations 

 
If the air heater is to be installed as a type B appliance, 
air for combustion will be taken from within the space 
where the heater is installed. 
 
Single wall flue seamless aluminium or stainless steel 
pipes are required. All joints must be sealed to prevent 
products of combustion from leaking into the building.  If 
the flue passes through a combustible element of the 
building it must be enclosed by a sleeve of non-
combustible material and separated from the sleeve by a 
minimum of 25 mm air break. The temperature of any 
combustible material near to the flue must not exceed 
65°C when the heater is in operation. The flue must be at 
least 150 mm away from any combustible material. 
 
Single wall flue pipe exposed to cold air or run through 
unheated areas should be insulated. Where 
condensation is unavoidable, provision must be made for 
the condensation to flow freely to a point to which it can 
be released, i.e. a drain or gully. The condensation drain 
from the flue must be constructed from non-corrodible 
material not less than 20 mm diameter. Copper or copper 
based alloys must not be used for condensation drains. 
 
For testing, the flue pipe should include a sealable test 
port. The port must be at least 450 mm away from the air 
heater flue connection socket.  
Follow the flue pipe manufacturer’s installation 
instructions for making joints, including connections to 
the air heater, for passing through a building element 
and for support requirements.  
 

 

6.2.2 Air 

supply 

 
Ensure that an adequate air supply for combustion and 
ventilation is provided within the building in accordance 
with BS6230/BS5440 plus other relevant regulations & 
rules in force.  
It is important to ensure that there is an adequate air 
supply at all times for both combustion and heating 
requirements.  
Modern buildings involve greater use of insulation, 
improved vapour barriers, and weather proofing. These 
practices mean that buildings are sealed much tighter 
than in the past. 

 

Proper combustion air supply for a power vented Type B 
installation requires ventilation of the heated space. 
Natural infiltration of air may not be adequate. Use of 
exhaust fans aggravates this situation. It is important to 
ensure that there is adequate combustion air supply at 
all times. Reliance on doors and windows is not allowed.  

 

Ensure that the air combustion inlet opening at the side of 
the unit cannot be obstructed (cfr. fig 7b). 
 

 

When these air heaters are installed in type B 
applications, designed to take air for combustion 
from the space in which it is installed. Do not 
restrict the combustion air intake. 

 
 

 

Figure 7a : Approved appliances type B 

B52/B22* – Roof

 

 

* : only Belgium

 

B52/B22* – Wall 

 

 
 
 
Figure 7b : Type B appliances – Combustion air and 
flue pipe sockets 

 

 

 

 
 
 

1  Combustion air inlet opening 
2  Flue pipe outlet collar 

Summary of Contents for BSHH 055






























Reviews: