background image

  37

   Video wall installation guide

Optimizing the video wall performance and management: PL460/ 
PH460/PL550/PH550

To optimize the video wall performance, change the OSD settings as suggested.

1.  Make sure the displays have been looped by IR, RS-232, or RJ45 connection.
2.  Go to 

Setting

 > 

Advanced

 > 

Overscan

 and set it to 

Off

.

3.  Go to 

Screen

 > 

Display Wall

 > 

Frame Comp.

 and set it to 

On

.

4.  Go to 

Screen

 > 

Display Wall

 > 

LED

 and set it to 

Off

.

5.  Go to 

Screen

 > 

Display Wall

 > 

Power On Delay

 and set it to 

On

.

• You are provided with BenQ software to fully utilize the video wall management. Visit the 

BenQ local website for the software and the user manuals.

Software

Description

Multi-Display 
Administrator

 (

MDA

)

A software program that enables remote and centralized 
management of a single or multiple BenQ digital signage displays 
on a host computer. You can create and edit display groups, view 
status of displays as well as change display settings.

Use an appropriate RS-232C cable. Refer to the user manual or BenQ 

service for more information.

Contact the BenQ customer service center for demonstration videos if 

needed.

Color Management

A software program that enhances the image uniformity of all 
displays in a video wall application. You can also adjust color 
settings of each display easily on a host computer, or backup and 
restore calibration data quickly.

Use an appropriate RS-232C cable. Refer to the user manual or BenQ 

service for more information.

Contact the BenQ customer service center for demonstration videos if 

needed.

Summary of Contents for PH460





















































































Reviews: