background image

Bennett Pulser Assembly Instruction Manual 

Installation Instructions 

SECTION 3: INSTALLATION INSTRUCTIONS 

Bennett Pump Dispensers are to be installed by trained technicians. All technicians must be aware of ALL safety instructions. If you are 
not a Bennett trained technician, please contact Bennett Technical Support at 1-800-423-6638 for training information. 

HOW TO REMOVE PULSER COVER 

Remove the Pulser cover and set aside. Retain screws for reuse.  

Note:  

 

After installation is complete, replace cover using the screws provided.   

 

The “Sealed” pulser cover shown below is optional.  If it is present, please check the requirements by the AHJ to put the pump 
back into service. 

 

 

 
 
 

HOW TO MOUNT THE PULSER ASSEMBLY  

The Pulser Assembly measures 4” x 2” x 2””. Each Pulser requires two mounting screws for the mount, and 2 mounting screws for the 
cover to the mount. 

1.

 

Mount Pulser by aligning roll pin in coupler slot.   

2.

 

Mount bracket screws to the top of the meter cover using the screws provided. Tighten firmly. 

3.

 

After the pulser is mounted and installation is complete, replace cover and seal if necessary.  

 

HOW TO CONNECT PULSERS 

CAUTION:  WHEN CONNECTING A PULSER NEVER CONNECT A PULSER OR DISCONNECT A PULSER WITHOUT TURNING OFF 

THE DISPENSER POWER AND BATTERY. DAMAGE TO THE PULSER OR THE LOWER I/O BOARD CAN OCCUR IF 
POWER IS LEFT ON.
 

MOUNTING HOLE 

MOUNTING HOLE 

1.

 

Seal Wire is Thread thru the 
Meter Collector cover bolts, 
then up to the bolt 
connecting the cover to the 
meter top. 

2.

 

The seal wire then threads 
from the pulser cover through 
the standoffs holding the 
pulser 

3. After the Seal Wire is thread 
through both pulser mounting 
standoffs, is routed back down to 
the Meter mounting adaptor. 

Summary of Contents for PULSER




















Reviews: