background image

BJ300GS-3

21

RIGHT HANDLE

1. ENGINE STOP SWITCH 

   When the switch is on "        " position and the power is on, the engine runs.
   When the switch is on "         " position and the power is off, the engine will not run.

2. HAZARD SWITCH”     ”

Turn to “   ” and the four direction signal lamps would flash to warn for emergency 

situation;turn to "

" for daytime driving.

3. ELECTRIC STARTER BUTTON

Pull the clutch lever or put in Neutral gear and press the button to run the electric 

motor and start the engine.

4. LIGHT SWITCH

Turn switch to position of "       " to light up the front lamp; Turn to "           " to light 

up meter lamp, city light and tail lamp; turn to "

" for daytime driving.

5. METER FUNCTION BUTTON

In ODO mode, turn off the key.  To adjust the clock, turn on the key switch and immediately
long press the set button, when released, the hour digit will start flashing on the meter.  
Short press the set button to change the number, or long-press to move the flashing digit 

PRIMARY PARTS

    Note

Under normal conditions, this switch shall be on "Operate" (        ) 

position. Use this switch under emergency situation, for example accident 
or key switch problems.

1
2

5

3

1
4

3

or

Without Headlight Switch

With Headlight Switch

5

Summary of Contents for BJ300GS-3




















































Reviews: