manualshive.com logo in svg

Benefon SERAPH NT, Operating Instructions Manual

Share
Download
Benefon SERAPH NT Operating Instructions Manual Download Page 52

PART G: IMPORTANT SAFETY INFORMATION

52 SAFETY AND PRECAUTIONS

General

•

Traffic

:

 Strictly adhere to all eventual European and

national legislation and also honour other eventual safety
recommendations when using the device while driving a
vehicle. Place the device in its holder, do not leave it on
the passenger seat or some other place where it can break
loose in a collision or a sudden stop. When receiving a
call in an awkward driving situation, you must always put
safety before other priorities and courtesy. If you feel
uncomfortable about using a device while driving, you
should not use it. 

•

Vehicles with air bags

: An air bag inflates with great

force. Do not place objects, including either installed or
portable wireless devices, in the area over the air bag or in
the air bag deployment area. 

•

External alert

:

 The use of the alert device to operate a

vehicle´s lights or horn on public roads is not permitted.  

•

Children

:

 Keep the device and its accessories away from

small children to avoid causing injury to themselves or
others. Damage to the device or its accessories is also thus
avoided.

•

Power supply

:

 

This equipment is intended for use with

the specified power supplies listed in the

 Quick Guide/

Operating Instructions. 

Any other usage will invalidate any

approval given to this apparatus and may be dangerous.   

•

Other accessories

:

 Any other accessories used should

also be approved by the device manufacturer. Check the
compatibility of new power supply units and other acces-
sories at the dealer or manufacturer.  

•

Connections

: All installations, connections and service

regarding the device, its power supply and accessories
should be approved by the device manufacturer. Use of
any unauthorized accessories, modifications or attach-
ments may be dangerous and voids the device warranty if
said accessories cause damage or a defect to the device.

•

Magnetic fields

: The device contains small magnetic

components. Even though the magnetic fields of the com-
ponents are weak, they might damage magnetic cards,
such as bank and credit cards. We recommend that you
would keep the device away from magnetic cards. 

•

Storing positions

: Position information is stored cor-

rectly in the device when the GPS is turned off (from the
GPS menu) or powered off (by pressing the upmost side
key). To prevent the memory from becoming corrupted,
never power off  the device by removing the battery.    

Summary of Contents for SERAPH NT

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands