Benefon SERAPH NT Operating Instructions Manual Download Page 32

Page: 32 / 56

PART C: OPERATING THE SERAPH

32 USER INTERFACE

Turning the device off

1. To power off the device, press the upmost side key

and hold it down for a few seconds. Note that some con-
figurations do not allow the device to be turned off nor-
mally.

2. The logo will be shown and the

Power off

tone heard.

3. The device may also notify the service center of the pow-

er off. For more information, see

SETTINGS FOR MANUAL

POWER ON AND OFF ON PAGE 27

Adjusting volume

To adjust speaker volume during a call, press the lower side
keys briefly.

•The

key increases the volume

•The

key decreases the volume.

Silencing alert tone

When the device alerts of an incoming call, the alert tone
can be silenced by pressing the lower side key

briefly.

About tone notifications

Tones are played through the loudspeaker simultaneously
when corresponding notifications are displayed. There are
several different tones informing of various situations.

Display indicators

POSITIONING

INDICATORS

ATTERY

INDICATOR

NETWORK

INDICATORS

ETWORK

OPERATOR

SERVICE

PROVIDER

IDENTIFIER

EVICE

STAND

MODE

GPS is active

GPS is sleeping

GPS is turned off /GPS has encountered an error

Bars on the left indicate accuracy of the latest
position fix

; The more bars and the taller the bars,

the better the position.
- Four bars - the most accurate position
- No bars - no position.

POSITIONING

STATUS

Summary of Contents for SERAPH NT
























































Search results

Summary of Contents for SERAPH NT

Reviews:

Brands by name

Popular brands

Benefon SERAPH NT, Operating Instructions Manual

Search results

Summary of Contents for SERAPH NT

Reviews:

Brands by name

Popular brands