Benchmark Scientific Incu-Shaker CO2 Mini Operating Manual Download Page 3

 

 

1. General Information and Precautions 

 

Safety Symbols: 

 

 

 

 

 

1.1. Precautions related to the power cable 

Always allow at least 3cm between the power cable and the back wall to prevent the back wall from causing 

pressure on the power cable. 

 

Always use the electrical plug that was supplied with this instrument.   

 

            

Never touch the power cord with wet hands. (This can result in electric shock.) 

 

Never use a damaged power cord or power outlet. 

 
 
In the event of smoke or a burning smell, immediately remove the power cord from the outlet. 

 

 

 

 

1.3. Precaution for use 
 

Do not attempt to disassemble this instrument.  If service is required, please contact your local 
representative. 

 

 

Never operate a flammable spray near this instrument. (This can result in a fire hazard.) 

 

 

Always use caution when using flammable substances such as benzene, alcohol 

and LP gas.    (Failure to do so can result in a fire hazard.) 

 

Prevent foreign substances from contacting the door seal. (The inflow of outside  air can negatively 

impact the temperature in chamber.) 

 

  Permissible ambient temperature range for transport: -10

 

to 60

.

 

 

 

Summary of Contents for Incu-Shaker CO2 Mini














Reviews: