background image

Attract Movement 

m the home position over the playfield, drops into the merchandise, raises, and 

Disabled 

Auto Playfield Floor Adjustment 

 floor height to maintain full look when enabled. 

isabled 

 

rogramming Options 

ption # 

Description 

0                      

Reset Defaults

.  Set to 2 and exit.  Resets factory default program settings and 

is adjustment sets the number of coins required for one play. 

n be played for free.  

he 

r attract cycles.  Default setting 

ming values. 

 

hanging the program settings

The claw moves fro
returns home (simulated game play) approximately every 5 minutes when enabled.  
 

Enabled 
 
 

The crane automatically adjusts the

 

Dip 8 

D
Enabled 

 

P
 

O
 

resets credits to 0   

Coins Per Play.  

Th

Game Play Timer

.  This adjustment controls the game countdown speed.  Range 

is 60-99.  Default setting is 72. ( min time is 22 seconds) 

Free Play Mode

.  Sets the number of minutes the game ca

After the programmed time has elapsed, the game returns to normal play mode. 

Attempts per credit

.  Sets the maximum number of attempts per credit that a 

player has to win a prize.  The game ends when a player wins a prize or when t
set value of attempts has expired.  Range is 1-99. 

Auto Plushing

.  Sets ratio of plushing routines pe

is 3, meaning the claw will plush once every three attract cycles.  Range is 1-23. 

Plushing Pull Height

.  Sets how many inches the claw will lift the plush before 

releasing during a plushing routine.  Range is 1-10.  Default is 4. 

Default Reset.

  Set this value to 2 and exit to reset default program

Exit.   

C

 

1.  To enter the programming mode, press the SW2 button

 

1

 on the 

power distribution pcb

2

.  The 2 digit credit display

3

 on the 

control panel will read A9. 
Bump the joystick

2. 

4

 up or down to rotate through the 

3. 

Dip 7 

On  
Off 

On  
Off 

programming option numbers 
Bump the joystick to the right to view the option value.  The 
decimal will light up indicating that the option value is being 
displayed and not the programming option number. Continue t
bump the joystick to the right in order to change the value. 

 

9

Summary of Contents for Acme Crane Company























Reviews: