10
11
Overview of Programming Options
Press the REV button
to go from one category
to the next
PILOT LIGHT
(Power-on indication)
POWER-ON SEQUENCE
SIGNAL STRENGTH METER
AUTOMUTE
VOICE**
CITY MODE SENSITIVITY
BRIGHTNESS
BANDS
*
RX75 PLUS’s Factory Default Settings
To reset RX75 PLUS to its original
factory settings, press and hold the
“CITY” and “VOL/MUTE” buttons
while turning the power on. The
RX75 PLUS’s display will provide a
“Reset” message, accompanied by
an audible alert, acknowledging the
reset.
**
Available only with External Speaker
Pilot HWY
Pilot H
Pilot V
PwrOn STD
PwrOn FST
Meter STD
Meter THT
Meter TEC
aMute ON
aMute OFF
Voice On
Voice Off
City STD
City LoX
City NoX
Brt AUTO
Brt MIN
Brt MED
Brt MAX
Brt DARK
Bands ALL
Bands MOD
X
ON
or
OFF
K
ON
or
OFF
Ka
ON
or
OFF
LSR ON
or
OFF
or
BLCK
SWS ON
or
OFF
Press the CHANGE button
to change your setting
within a category
*
Full word: Highway or Auto or City
Letter: H or A or C
Vehicle voltage
*
Standard power-on sequence
Fast power-on sequence
*
Standard signal strength meter
Threat Display
™
TechDisplay
*
AutoMute on
AutoMute off
*
Voice on
Voice off
*
Standard City mode sensitivity
Low X-band sensitivity in City Mode
No X-band sensitivity in City Mode
*
Brightness adjusts automatically
Minimum brightness
Medium brightness
Maximum brightness
Dark Mode
*
All bands enabled
One or more bands has been modified
Turn bands “ON” or “OFF” by holding
down the VOL/MUTE button
Details of Programming Options
Pilot Light (Power-on indication)
Note: When you are using the Dark mode,
the display will only show HD, AD, or CD,
(Highway-Dark, AutoScan-Dark, or City-
Dark).
PilotHWY
(Full description)
In this setting, the RX75 PLUS will display
“Highway,” “City,” or “AutoScan” as its
power-on indication. (factory default)
Pilot H
(Letter)
In this setting, the RX75 PLUS will display
“H” for Highway, “C” for City, or “A” for
AutoScan.
Pilot V
(Vehicle voltage)
In this setting, the RX75 PLUS will display
“H” for Highway, “C” for City, and “A” for
Auto, and the vehicle’s voltage. If the
vehicle’s voltage drops below 10.5 volts, a
low voltage warning will be displayed,
followed by an audible alert. A high voltage
warning is also given when the vehicle’s
voltage goes above 16.0 volts.
Power-on Sequence
PwrOnSTD
(Standard)
In this setting, each time you turn on the
RX75 PLUS, it will display “BEL PRO,”
“RX75,” “Laser,” “Ka-band,” “K-band,”
“X-band,” followed by a brief X-band alert. It
then confirms communications to all of its
components. If a communications error
occurs, the appropriate error message will
be displayed. (see page 21 for error messages)
Note: If there is a problem with the front
laser receiver or wiring after the initial
start-up sequence, the RX75 PLUS will
briefly display “LsrF ERR.” If there is a
problem with the rear laser receiver or
wiring after the initial start-up sequence,
the RX75 PLUS will briefly display “LsrR N/A.”
In both cases, the RX75 PLUS will
continue to receive radar signals, but will
not receive laser signals. If there is a
problem with the front radar receiver or
wiring after the initial start-up sequence,
the RX75 PLUS will display “Front N/A,”
and will then continue to display “Check,”
“Receiver,” “Wiring.” The RX75 PLUS will
not operate in this condition. Please
contact your installer if this occurs.
PwrOnFST
(Fast power-on)
This setting shortens RX75 PLUS’s start up
sequence to a single beep, eliminating the
words “BEL PRO,” “RX75,” “Laser,”
“Ka-band,” “K-band,” “X-band,” from the
start-up sequence.
