background image

Specifications (USB Series)

19

INPUT

Capacity 350VA(227W)

500VA(300W)

650VA(390W)

Voltage

187 Vac - 280 Vac

Frequency 50Hz 

or 

60Hz 

±

3Hz (auto sensing)

OUTPUT

Voltage Simulated 

sine 

wave, 

230 

Vac

±

8% 

(on battery)
Frequency 50Hz 

or 

60Hz 

±

1Hz

(on battery)

MODEL

350VA

500VA

650VA

Voltage 
Regulation
AVR

Smart boost increases 14.8% of voltage if input is 213 to 187 Vac. 

Smart trim reduces 12.8% of voltage if input is 247 to 288 Vac

UPS output cut off immediately or input breaker protection

Transfer Time

< 4 milliseconds, including detection time

Spike Protection

PROTECTION
AND FILTERING

Overload Protection

Modem/Network

Single Line (2 Wire, RJ11) Network (UTP, RJ45) compatible
jacks, one input/two output

Unit Input

Breaker for overload and short circuit protection

UPS automatic shutdown if overload exceeds 130% in AC
mode and 100% in back-up mode. UPS alarms continuously
in > 107% or <130% in AC mode.

Short Circuit

Depending on computer load...

Type

Protection

Automatic self-test and discharge protection,
replace battery indicator

Typical
Recharge Time

4 hours (to 90% of full capacity)

Sealed, maintenance-free lead acid 

BATTERY

PHYSICAL

ALARM

ENVIRONMENT

INTERFACE

CONFORMANCE

Full/half load

Back up Time

Net Weight
Dimension 
(mm) WDH
Input inlet 
Output outlet (UPS)

289 x 243 x 325 

5.5kg/12.3lbs.

5-20 min

5-30 min.
6kg/13.23lbs

5-45 min

10A/250V*1pcs, EN60320

10A/250V*4pcs; ENG60320/F
10A/250V*4pcs; ENG60320/F

Output outlet
(Bypass)
Battery Back-Up

Slow beeping sound (about 15 sec. interval)
Rapid beeping sound (about 1 sec. interval)

Battery Low
Overload
Fault
Battery test
USB Interface
Safety
Surge
Ambient operation
Audible noise

Continuous beeping sound (about 1 sec. interval)
10 sec. beeping sound continuously
Slow beeping sound (about 15 sec. interval)

-15

°

C – 40

°

C (with battery)

-15

°

C – 70

°

C (without battery)

USB Port
CE, TUV/GS, TUV/EMC,EN5009-1-1-1, EN50091-2, EN50082-1
Meet IEEE C62.41. Category A standard
0~95%, humidity non-condensing, 0~40

°

<40dBA (1 meter from surface)

150 Joules

6.5kg/14.33lbs.

Storage condition

En

P73220uk_Gold_UPSMan  27-05-2002  15:02  Page 19

Summary of Contents for F6C325-220V





















Reviews: