manualshive.com logo in svg

BELGACOM Forum 523, Mounting And Commissioning Manual

Share
Download
BELGACOM Forum 523 Mounting And Commissioning Manual Download Page 62

Power Failure

60

Installation

Power Failure

In the event of a power failure, all configuration data, voice box 
messages as well as account data are preserved. The internal 
clock will continue to run for about 24 hours. If the power failure 
lasts for more than 24 hours, the time and date are reset to the 
factory settings when the power is switched on again. Depending 
on the 

System

: 

Common

: 

Synchronize Time

 setting, date and 

time are set to the current values on the first outgoing call as pro-
vided by the exchange.

Please note:

Do not reset the Forum 523/524 by pulling the 

plug. Actual configuration changes may be lost and reconnecting 
to a SIP provider may need a longer time. Use the code number 
procedure 

* 1 8 5

[System PIN]

#

 instead. 

Summary of Contents for Forum 523





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands