BEKOMAT 32iU Translation Of Original Installation And Operation Manual Download

Page: 48 / 68

Exchange work

Illustration

Description / explanation

Power

Alarm

Service

TEST

5. Press the TEST button

[A]

on the control unit and hold

it for at least 5 seconds.

The green POWER LED flashes

6. Once the green POWER LED is permanently lit, release

the TEST button.

The “Remaining service time” counter (Modbus

address 3103 / 3104) is reset

The “Remaining switching cycles” counter (Modbus

address 3105 / 3106) is reset

7. Lay the control unit

[A]

carefully to one side.

8. If a design shell

[8]

is attached, carefully lift the design

shell

[8]

to the marked positions using a flat head

screwdriver.

9. Carefully remove the design shell

[8]

10. Remove the hose connection

[9]

with the hose

[X3]

BEKOMAT

32iU

Original installation and operation manual

48 | 68

Summary of Contents for 32iU





































































Search results

Summary of Contents for 32iU

Reviews:

Related manuals for 32iU

Brands by name

Popular brands

BEKOMAT 32iU, Translation Of Original Installation And Operation Manual

Search results

Summary of Contents for 32iU

Reviews:

Related manuals for 32iU

Brands by name

Popular brands