background image

Installation 

16 

 

BEKOBLIZZ® LC 12-355 

8.3 Correction 

factors 

Correction factor for operating pressure changes: 
Inlet 

air 

pressure    bar(g) 

4  5  6  7  8  10 12 14 15 

Factor (F1) 

0.77 

0.86 

0.93 

1.00 1.05 1.14 1.21 1.27 1.30 

 

Correction factor for ambient temperature changes (Air-Cooled): 
Ambient temperature      

    ºC 

 

25 30 35 40 45 50 

Factor 

(F2) 

1.00 0.96 0.90 0.82 0.72 0.60 

 

Correction factor for inlet air temperature changes: 
Air temperature  

                 ºC 

 

25 30 35 40 45 50 55 

Factor 

(F3) 

1.39 1.20 1.00 0.80 0.63 0.51 0.46 

 
Correction factor for DewPoint changes: 
DewPoint  

 

 

    ºC 

10 

15 

20 

Factor 

(F4) 

0.88 1.00 1.04 1.15 1.42 1.82 

 

Calculation of the actual air throughput:

 

Actual air throughput = air throughput acc. to planning x factor (F1) x factor (F2) x factor (F3) x factor (F4) 

Example:

 

The 

BEKOBLIZZ LC 240

 has a planned nominal capacity of 

240 m³/h

. The highest achievable air mass 

under the following operating conditions is:  

  Air inlet pressure = 8 bar(g) 

  Ambient temperature = 35°C 

  Air inlet temperature = 40°C 

  Pressure dew point = 5°C 

 Factor (F1) = 1.05 

 Factor (F2) = 0.90 

 Factor (F3) = 0.80 

 Factor (F4) = 1.00 

Every function parameter corresponds to a numerical factor which, multiplied by the planned nominal capacity, 
determines the following: 

Actual air throughput = 240 x 1.05 x 0.90 x 0.80 x 1.00 = 181 m³/h 

181 m³/h

 is the maximum flow rate of the chiller under the aforementioned operating conditions. 

 

Selection of the best suitable model in accordance with the operating conditions:

 

Air throughput acc. to planning =  

Requ. air throughput 

 

Factor (F1) x Factor (F2) x Factor (F3) x Factor (F4) 

Example:

 

The following operating parameters are known: 

  Required air mass = 100 m

3

/h 

  Air inlet pressure = 8 bar(g) 

  Ambient temperature = 35°C 

  Air inlet temperature = 40°C 

  Pressure dew point = 5°C 

 

 Factor (F1) = 1.05 

 Factor (F2) = 0.90 

 Factor (F3) = 0.80 

 Factor (F4) = 1.00 

To find out the correct chiller version, the required air mass must be divided by the correction factors of the 
parameters indicated above: 

Air throughput acc. to planning = 

100 

= 132 m³/h 

1.05 x 0.90 x 0.80 x 1.00 

The suitable model for these requirements is 

BEKOBLIZZ LC 150

 (with a spec. nominal capacity of 150 m³/h). 

Summary of Contents for Bekoblizz LC 12-355

































































Reviews: