BEIER-Electronic SV1-2-10Z Instruction Manual Download Page 5

GB  

Controller 

SV1-2-10Z 

 

 
GB_SV1-2-10Z.DOC    1003 

BEIER-Electronic 

 
 

General Description of the Device 

 
Power unit 

 

The SV1-2-10Z is a control device for oscillation conveyor drives with electromagnets 
and works according to the principle of a frequency converter. This control is setting 
standards as regards feeding performances, operating comfort and energy savings. 

 

In spite of its very compact construction design the control device SV1-2-10Z covers 
the performance range that is usual with vibration feeding devices. As standard finish 
the device is equipped with soft start and soft run-out, which can both be adapted at 
any time to the connected oscillation conveyor drive.  
By means of the external, potential-free control input 10 - 30V AC or DC, the  
SV1-2-10Z can be enabled or disabled.  
In applications with frequent switching functions (e.g. level control), the 
controller may be not constantly switched via the mains voltage!  In this case 
the control input must be used, since otherwise the life span of the controller 
is limited! 
All settings, like e.g. set-point input or frequency input are done by means of  menue-
assisted key inputs at the front plate. 
A 16-digit LC-Display and a status LED inform at any time about the current state of 
the SV1-2-10Z. 
The electronic current control prevents a possible overload of the control device and 
the conveyor system. 
Within the indicated limit values there is no setting required for the mains voltage and 
mains frequency. 
 

Power supply 

The SV1-2-10Z disposes of a switch-controlled 24V DC power pack. It is used for the 
supply the internal time function elements, the connected proximity switches and the 
outputs (blast air, control output). The power pack is short circuit-proof and can 
supply current of max. 1,5A. 

 

Time function elements 

The integrated time function elements have an extensive logic (see page 10+11). A 
total of 8 times is available enabling the realisation of different functions. These times 
can be set from 0,0 to 25,0 seconds. 
 
The SV1-2-10Z is compatible with control SV1-2-10Z. Furthermore, by means of an 
optional Input a 2-Sensor min/max level control is also possible. 
 
By a second, adjustable, set-point value e.g. single counter operations can be dosed 
more exactly. 

Summary of Contents for SV1-2-10Z























Reviews: