BEIER-Electronic SV1-2-10Z Instruction Manual Download Page 20

GB  

Controller 

SV1-2-10Z 

 

 
GB_SV1-2-10Z.DOC    1003 

BEIER-Electronic 

20 

 
 

Technical Description 

 
Change I-MAX  

 

Upon switching the DIP-Switch S12.4 to position ON, the maximum current, which 
flows into the connected feeding device can be limited. 

  

B     0  5  0  % = 1  ,  2  A    2  ,   5  A 

 

Maximum current     

 

Current range  

 

By means of the key 

 and 

 a new maximum current can be entered. Values 

between 10% and 100% are admissible. The given percent values refer always to the 
set current range (2,5A or 10A). The value is stored upon actuating key  

. It must 

be observed, that the feeding device cannot be overloaded by the operator! After the 
adjustment the DIP-Switch S12.4 has to be set back to position OFF. 
 
Set-point value 2 

 

By means of the DIP-Switch a second set-point value can be made possible. If the 
switch is in position ON both set-point values are displayed in menue line “A”. The 
change over between set-point value 1 and 2 is done by means of Input X13. If this 
input is selected set-point value 2 is active, otherwise set-point value 1. 

 

Current range 

 

Generally 2 current ranges are available. If the DIP-Switch S12.6 is in position OFF 
the SV1-2-10Z supplies an output current of 2,5A maximum. In position ON the 
feeding device disposes of 10A at most.  
Attention: In case of currents higher than 6A the device has to be mounted on 
a heat sink! 

 

Current waveform 

 

Two different output current waveforms are possible which can be selected by the 
DIP-Switch S12.7. At position OFF the current is trapezoidal at position ON nearly 
sinusoidal. The current waveform which is better for the respective feeding device 
(feeding performance, noise level, current input) must be found out by testing. At 
frequencies less than 40Hz, the sinusoidal current waveform is recommended. 
 
Additional information regarding control SV1-2-10Z 

 

Even if the control unit is switched off by the main switch Q1 or 
disconnected from the voltage supply the inner side of the device 
remains energised (dangerous to life). The device is reenergised 
when ‚ POWER OFF ‘ expires on the display and the status LED 
H1 is dark. This can take up to 20 seconds. Before this the device 
must not be opened! 

 

Summary of Contents for SV1-2-10Z























Reviews: