ENGLISH
OPERATION
MANUAL
JB SYSTEMS®
1/20
LED GROUND LIGHT
Thank you for buying this JB Systems product. To take full advantage of all possibilities and for your own
safety, please read these operating instructions very carefully before you start using this unit.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
•
This device has been designed to produce decorative effect lighting and is used in light show systems.
•
Mechanically very strong multicolor RGB ground light, used for borders in parkways, entrances of
discotheques, buildings, parkings, homes, etc.
•
Can also be used in al kinds of stone brick and concrete walls and ceilings.
•
To be used with the LED-MANAGER (dmx power supply)
•
39 very bright LEDs behind a thick milky translucent glass cover.
•
All-weather proof IP67 design with stainless steel cover ring.
•
Can be built-in any concrete (or other) floors, walls and ceilings.
•
Very easy electrical connection: 4-wire connection.
•
16cm overall diameter
•
Longlife LED Technology!
•
Power consumption = 3W only!
BEFORE USE
•
Before you start using this unit, please check if there’s no transportation damage. Should there be any, do
not use the device and consult your dealer first.
•
Important:
This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused
by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects
or problems caused by disregarding this user manual.
•
Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
Check the contents:
Check that the carton contains the following items:
•
Operating instructions
•
LED ground light unit
SAFETY INSTRUCTIONS:
•
To protect the environment, please try to recycle the packing material as much as possible.
•
This unit has protection class IP67 so it can be used outdoors when it is properly installed.
•
Inexperienced persons should not operate this device.
•
Maximum save ambient temperature is 45°C. Don’t use this unit at higher ambient temperatures.
•
The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
•
The cables should always be in perfect condition: switch the LED Manager immediately off when the
cables are squashed or damaged.
•
This appliance must be used with the LED Manager: don’t connect the unit to any dimmer pack or other
power supply.
•
In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
•
The housing and the lenses must be replaced if it is visibly damaged.
•
Please use the original packing when the device is to be transported.
ENGLISH
OPERATION
MANUAL
JB SYSTEMS®
2/20
LED GROUND LIGHT
•
Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important:
Don’t use the effect in the presence of persons suffering from epilepsy.
DESCRIPTION:
1. Strong stainless ring with 3 bolts used to keep the glass cover safely in place.
2. Strong glass cover with rubber sealing to ensure the enclosure is waterproof.
3. 3 screws used to fix the waterproof metal body inside the plastic niche mounting box.
4. Waterproof metal enclosure with LED lights inside.
5. Plastic niche mounting box used to install the projector in the floor (or wall/ceiling)
6. 4 special “press on” wire connections.
MECHANICAL INSTALLATION
•
Important:
The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Certified installation materials
should be used, the installed device should be inspected regularly for safety.
•
Make sure the area around the installation place is free from unwanted persons during installation and
servicing.
•
Separate the plastic niche
mounting box (5) from the rest of
the projector.
•
First install the mounting box at
the right spot in the floor. See the
drawing for more information.
•
Close the projector after
connecting the electrical wires
(see next chapter)
•
Make sure the wire inlet on the
waterproof metal housing is well
fastened and sealed so that no
water can come in.
•
Fix the metal enclosure to the niche mounting box using the 3 screws.
•
Make sure the collar on the upper side of the metal housing is free from dirt or dust.
•
Make sure the glass cover and its rubber sealing are clean and put them in place.
•
Install the stainless metal ring and fasten with the 3 special bolts.
