Bedfont ToxCO Page 33 User Manual Download | Manualshive

Page: 33 / 44

background image

32

Calibration

The ToxCO®

is calibrated at 21°C (±4°C) before leaving Bedfont®.

The ToxCO® must be calibrated within 17-

25°C as this is the temperature at which Bedfont® recommend it is to be used.

It is recommended that the ToxCO® is calibrated every 6 months, however a calibration MUST be

performed within 12 months, using 50ppm CO calibration gas. Please refer to the ‘calibration procedure’

for more information.

Turn on the monitor by pressing the power button once.

Press the settings icon.

Press the cylinder icon once to proceed.

«
...
31
32
33
34
35
...
»

Summary of Contents for ToxCO













































Reviews:

No comments

Related manuals for ToxCO

Brand: Autostart Pages: 4

Brand: CrimeStopper Pages: 16

Brand: CrimeStopper Pages: 20

Brand: Crime Guard Pages: 82

Brand: AVS Pages: 4

Brand: AVS Pages: 12

Brand: CrimeStopper Pages: 4

CS-9200 Samurai

Brand: CrimeStopper Pages: 3

Brand: Avital Pages: 25

Brand: jablotron Pages: 16

Brand: LaserLine Pages: 24

Brand: Honeywell Pages: 12

Brand: United Technologies Pages: 25

991 Responder LC3

Brand: Python Pages: 80

Brand: Audiovox Electronics Pages: 12

KN-COB-B-LS (900-0233)

Brand: Kidde Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands