Beckman Coulter Avanti J-26 XP Series Instructions For Use Manual Download Page 68

Page: 68 / 76

J326XP-IM-5AB

5-4

Care and Maintenance

Maintenance

Replacing the Air Filter

Check the air filter regularly and replace it about once a year, or more often if it looks dirty.

•

The air filter is not fastened to the centrifuge, so no tools are required for removal or
installation.

To remove the air filter, hold the side edges and lift the filter straight up until the bottom edge
is above the centrifuge bottom retaining strip.

Pull the filter out, bottom edge first, and discard it.

Install a new filter (885218).

The filter has a directional arrow on one of its edges; install the filter with this arrow
pointing toward the centrifuge.

Holding the filter by the side edges, insert the top half behind the frame edge and lift up
until the bottom half clears the retaining strip.

Then set the bottom edge down.

Frame Edge

Air Filter

Retaining Strip

Frame Edge

Summary of Contents for Avanti J-26 XP Series












































































Search results

Summary of Contents for Avanti J-26 XP Series

Reviews:

Related manuals for Avanti J-26 XP Series

Brands by name

Popular brands

Beckman Coulter Avanti J-26 XP Series, Instructions For Use Manual

Search results

Summary of Contents for Avanti J-26 XP Series

Reviews:

Related manuals for Avanti J-26 XP Series

Brands by name

Popular brands