Beckman Coulter Avanti J-26 XP Series Instructions For Use Manual Download Page 45

Page: 45 / 76

J326XP-IM-5AB

3-5

Operation

Entering Run Parameters

Turn the

SPEED

knob until the required RPM appears in the

SPEED

display.

•

When the run is started, the centrifuge operates at the set speed.

•

The corresponding RCF is automatically calculated.

Press

RPM/RCF

to display the RCF value.

Setting RCF

Check to see if the red

RCF

light is lit on the display.

If it is lit, go to step 3.

Press the

RPM/RCF

key to select the

RCF

mode.

•

On the display, the red RCF (



) LED lights.

Turn the

SPEED

knob until the required RCF value appears in the

SPEED

display.

•

The centrifuge operates at a speed calculated to produce the set RCF value.

Press

RPM/RCF

to display the

RPM

value.

Setting Run Time

Pressing the

TIME/HOLD

key toggles the system between

HR:MIN

mode and

HOLD

mode.

HR:MIN

mode is the default.

Summary of Contents for Avanti J-26 XP Series












































































Search results

Summary of Contents for Avanti J-26 XP Series

Reviews:

Related manuals for Avanti J-26 XP Series

Brands by name

Popular brands

Beckman Coulter Avanti J-26 XP Series, Instructions For Use Manual

Search results

Summary of Contents for Avanti J-26 XP Series

Reviews:

Related manuals for Avanti J-26 XP Series

Brands by name

Popular brands