Beckman Coulter Avanti J-26 XP Series Instructions For Use Manual Download Page 50

Page: 50 / 76

J326XP-IM-5AB

3-10

Operation

Entering Run Parameters

Install the rotor.

Set up sample and buffer reservoirs and tubing lines as described in the rotor manual.

Route the tubing lines through the elutriator port holes at the left side of the door seal.

Close the centrifuge door.

Turn the

ROTOR

knob to the

position.

•

5.0 appears in the

ROTOR ID

display.

Enter the remaining run parameters. Refer to the JE-5.0 rotor manual for rotor setup and
operating instructions.

•

The run is ready to begin.

Press

START

•

The rotor accelerates to set speed.

When the rotor reaches set speed, turn on the strobe controls by pressing the strobe power
switch.

•

The power switch indicator lights.

Strobe Power Switch

ROTOR

JSP

JLA

JCF

ELUTRIATOR

DELAY

Summary of Contents for Avanti J-26 XP Series












































































Search results

Summary of Contents for Avanti J-26 XP Series

Reviews:

Related manuals for Avanti J-26 XP Series

Brands by name

Popular brands

Beckman Coulter Avanti J-26 XP Series, Instructions For Use Manual

Search results

Summary of Contents for Avanti J-26 XP Series

Reviews:

Related manuals for Avanti J-26 XP Series

Brands by name

Popular brands