manualshive.com logo in svg

Beckman Coulter Allegra X-14 sERIES, Instructions For Use Manual

Share
Download
Beckman Coulter Allegra X-14 sERIES Instructions For Use Manual Download Page 44

PN B07493AD

4-4

Care and Maintenance

Storage and Transport  

Storage and Transport

Storage

To ensure that the centrifuge does not get damaged, contact Beckman Coulter Field Service for 

specific instructions and/or assistance in preparing the equipment for transport or long-term 

storage. Temperature and humidity conditions for storage should meet the environmental 

requirements described under 

Specifications

 in 

CHAPTER 1

.

Supply List

Contact Beckman Coulter Sales or visit www.beckman.com for information about ordering parts, 

supplies, and publications. For your convenience, a partial list is given below.

Refer to the applicable rotor manual for materials and supplies needed for rotors.

Replacement Parts

Supplies

NOTE

For MSDS information, go to the Beckman Coulter website at www.beckmancoulter.com.

Descrilption

Part Numbr

Anti-rotation kit

392988

Description

Part Number

Silicone vacuum grease (1 oz)

335148

Beckman Solution 555 (1 qt)

339555

Program library record

233679

Summary of Contents for Allegra X-14 sERIES























































Reviews:

No comments

Brands by name

Popular brands

Load more brands