background image

Technical data

24

 

───

Version: 1.0

AMI8100

4.1

Definitions

Characteristic torque and speed curves

Detailed information on characteristic curves can be found under:
Beckhoff motor curves

All data, with the exception of the voltage constant, are based on
40 °C ambient temperature and 100 K overtemperature of the wind-
ing. The data can have a tolerance of +/-10 %.
If a gear unit is attached the power may be reduced by up to 20 %.

The A-side flange is intended for heat dissipation. If a gear unit is at-
tached, the heat dissipation is interrupted and reduces the power of
the servo drive.

By  default,  the  heat  is  dissipated  via  the  A-flange  into  the  machine
bed. Due to heating of the gear unit, this is not possible for thermal
reasons. This configuration leads to a reduction of the nominal out-
put.

4.1.1

Technical terms

This  chapter  provides  information  on  various  technical  terms  and
their meaning.

Standstill torque M

0

 [Nm]

Torque, also referred to as starting torque, that the servo drive can
generate at standstill. It can be maintained indefinitely at a speed n
< 100 min

-1

 and nominal ambient conditions.

Nominal torque M

n

 [Nm]

The torque that the servo drive delivers when it is operated at nomi-
nal speed and nominal current. Can be output in continuous opera-
tion S1 for an unlimited period of time.

Standstill current I

0rms

 [A]

Sinusoidal current RMS value. This is consumed at a speed of n <
100 min

-1 

in order to generate the standstill torque.

Peak current / pulse current I

0max

 [A]

Sinusoidal peak current RMS value. The configured peak current of
the servo drive used must be less or equal.

Torque constant K

Trms

 [Nm/A]

Indication of the torque in Nm generated by the servo drive per am-
pere of standstill current. The following applies: M

= I

0

 x K

T

Summary of Contents for AMI8100






























































Reviews: