BEAMEX MC6-Ex User Manual Download Page 12

Page: 12 / 116

4 MC6-Ex User Manual

– Part 1, Introduction

BOUT

MC6-E

TARTING

MC6-E

Start MC6-Ex by pressing the

Power

button for a few seconds. The startup pro-

cedure ends in

Home View

(see picture on the right). From MC6-Ex's

Home

View

you may advance to any of the available main functions. This manual con-

tains detailed information of main functions as follows:



Meter

in Part 3,



Calibrator

in Part 4,



Documenting Calibrator

in Part 5,



Data Logger

in Part 6,



Communicator

in Part 7 and



Settings

in Part 8.

With the

Home

button (see picture on the right) you can always return to

Home

View

from wherever you are.

When MC6-Ex is already running, pressing the

Power

button briefly opens a

dialog with the following options:



Power Off

to shut down MC6-Ex in

Backup Mode

, i.e. minimum power

consumption and full startup procedure.



Standby

to set MC6-Ex in

Standby Mode

allowing faster startup when

the

Power

button is pressed again.



Backlight Off

to temporarily set the backlight off.

The buttons available in the dialog (top to bottom):



Power Management

to define Backlight Brightness and other power

management related settings. More in Part 8,

Settings



MC6-Ex Safety Information

. Detailed information in

Appendix

Power button (left) and Home button (right).

Home View

Note.

Certain main functions are options. They may not be available
in your MC6-Ex. More of this in chapter Options on page 13.

Summary of Contents for MC6-Ex





















































































































Search results

Summary of Contents for MC6-Ex

Reviews:

Related manuals for MC6-Ex

Brands by name

Popular brands

BEAMEX MC6-Ex, User Manual

Search results

Summary of Contents for MC6-Ex

Reviews:

Related manuals for MC6-Ex

Brands by name

Popular brands