background image

+ -

75.5367.08 UL MAGLOCKS 1200lb 20210806  

Page 4 of 5

The product must be powered from a UL-listed, regulated, power-limited, power supply.

12 VDC INPUT

 - Required power:  0.5 AMP / 12 VDC
 - Connect positive (+) lead from a 12 VDC power source to Terminal 1.
 - Connect negative (-) lead from a 12 VDC power source to Terminal 2.
 - Check jumper for 12 VDC operation.

24 VDC INPUT

 - Required power:  0.25 AMP / 24 VDC
 - Connect positive (+) lead from a 24 VDC power source to Terminal 1.
 - Connect negative (-) lead from a 24 VDC power source to Terminal 2.
 - Check jumper for 24 VDC operation.

POWER

If power switch is not wired between DC source v) and magnet, it will take a longer time to de-energize the magnet simulating 

residual magnetism.

Page 2 of 2 

 

 

 

 

 

 

 

 

 

75.5366.02   20140401

5   Installation - Mechanical & Electrical

LOCK ST

ATUS SWITCH (SPDT)

POWER 

SUPPL

Y  

     +    -

POWER

SELECT

OR

JUMPER

LED

MAG BOND SENSOR

MAGNET

TIMER (0-90 SEC)

TYPICAL INSTALLATION

NOTE:  DO NOT over-tighten the armature plate.  The rubber washer is designed to allow the armature 

plate to automatically adjust position for best mating position between the lock and armature plate.

DOOR FRAME

ARMATURE PLATE

MAGNET

ANGLE

BRACKET

MOUNTING

PLATE

MOUNTING

PLATE

STRINGER

HOLE FOR

GUIDE PIN
HOLE FOR NUT

RUBBER WASHER
STEEL WASHER
ARMATURE PLATE

SCREW M8 (35MM)

GUIDE PIN

DOOR

NUT

SPACER

WASHER

ARMATURE

PLATE

DOOR

NUT

DOOR FRAME

DOOR FRAME

DOOR

ARMATURE PLATE

ARMATURE PLATE

MAGNET

MAGNET

DOOR

DOOR

MOUNTING

PLATE

CAUTION:  Observe proper 

circuit board orientation!

NOTE:  The product must be powered from a UL listed, regulated, power limited, power supply.
NOTE:  If power switch is not wired between DC source voltage and magnet,

             it will take a longer time to de-energize the magnet simulating residual magnetism.

1. 12 VDC INPUT
  

A.   Required power 0.5A (Max).
B.   Connect ground (-) lead from a 12 VDC power source to Terminal 2.
C.   Connect positive (+) lead from a 12 VDC power source to Terminal 1.
D.   Check jumper for 12 VDC operation.

2. 24 VDC INPUT

A.   Required power 0.25A (Max).
B.   Connect ground (-) lead from a 24 VDC power source to Terminal 2.
C.   Connect positive (+) lead from a 24 VDC power source to Terminal 1.
D.   Check jumper for 24 VDC operation.

3. CONTACTS

1.   Relay dry contacts are rated 1A at 24 VDC for safe operation, DO NOT exceed this 

rating.

2.   If a NO switch is required, connect the wires from the system to Terminal 4 & Terminal 3.
3.   If a NC switch is required, connect the wires from the system to Terminal 4 & Terminal 5.

DS VERSION

24/7 Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462 | General Tech Questions: [email protected] | Tech Docs: www.beasensors.com

7   Installation 

 Electrical (cont.)

Summary of Contents for 10MAGLOCK1UL






Reviews: