BD Alaris neXus GPneXus1 Directions For Use Manual Download Page 7 | Manualshive

Page: 7 / 74

background image

BD Alaris™ neXus GP Volumetric Pump

Overview

BDDF00558 Issue 5

6/72

Conditions for Use

The BD Alaris™ neXus GP Volumetric Pumps are restricted medical devices intended for use by qualified, trained personnel

to deliver either continuous or intermittent infusion therapy of:

•  Fluids
•  Medications
•  Nutritional supplements
•  Blood and blood products

Indications

The BD Alaris™ neXus GP Volumetric Pumps are indicated for delivery of therapies through the following clinically

acceptable routes

•  Intravenous (IV)
•  Subcutaneous
•  Irrigation of fluid spaces

Contraindications

The BD Alaris™ neXus GP Volumetric Pump is contraindicated for enteral or epidural therapies .

Undesirable Side-Effects

The BD Alaris

™

neXus GP Volumetric Pump has no undesirable side-effects associated with its use when used in

accordance with the Directions for Use .

Compatibility

The BD Alaris™ neXus GP Volumetric Pump is compatible with the following:

•  The Alaris™ Gateway Workstation v1 .3 .x and v1 .6 .x – see ‘Associated Products’
•  Standard, single-use, disposable infusion sets – see ‘Infusion Sets’
•  The Active RFID asset tag supplied by BD with this Pump
•  The following minimum versions of software products are also compatible – see ‘Products and Spare Parts’

-

BD Alaris™ neXus Editor v5 .0

-

BD Alaris™ neXus Transfer Tool v5 .0

-

BD Alaris™ Technical Utility v2 .0

-

BD Alaris™ Communication Engine v 2 .0

-

BD Alaris™ CQI Event Reporter V4 .4

«
...
5
6
7
8
9
...
»

Summary of Contents for Alaris neXus GPneXus1











































































Reviews:

No comments

Related manuals for Alaris neXus GPneXus1

Brand: Landoll Pages: 52

Brand: JBSYSTEMS Light Pages: 14

Brand: MacDon Pages: 89

Brand: Yates Pages: 2

Brand: JAC Pages: 100

Brand: Balanced Body Pages: 4

Brand: Maico Pages: 55

Brand: Maico Pages: 38

Brand: Maico Pages: 2

Brand: MAHA Maschinenbau Haldenwang Pages: 13

ENET-232 Series

Brand: National Instruments Pages: 105

Smart Plus PHT-35LHS

Brand: Vatech Pages: 190

Brand: ZOLL Pages: 37

Brand: Wacker Neuson Pages: 34

Brand: Wagan Pages: 4

Brand: Wachs Pages: 22

Brand: Easylife Pages: 3

Brand: York Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands