background image

SSS3416TBSN 
Owner’s Manual 

12

 

                                                                       

Natural Gas Connection 

 
 

 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 

During high pressure testing your gas grill and its individual shutoff valve must be disconnected from the gas supply piping 
system. During any pressure testing of that system at least pressures in excess of 1/2 psi (3.5kPa). 

 

During low pressure testing your gas grill must be isolated from the gas supply piping system by closing its individual manual 
shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.5kPa). 

 

Warning

: Burner valves are pre-tested at the factory to operate on natural gas. If you wish to convert or change it, be sure to 

contact your grill distributor or dealer FIRST! 

 DANGER 

To prevent fire or explosion hazard when testing for a leak: 

1.  Always perform the “leak test“ on page 14 before lighting the grill and each time the natural gas hose is connected for use. 
2.  Do not smoke or allow other sources of ignition in the area while conducting a leak test.   
3.  Conduct the leak test outdoors in a well-ventilated area. 
4.  Do not use matches, lighters or a flame to check for leaks. 
5.  Do not use grill until all leaks have been stopped. If you are unable to stop a leak, disconnect the natural gas supply, call for 

gas appliance service or your local natural gas supplier. 

Checking for Leaks

 

1.    Make 2-3 oz. of leak solution by mixing one part liquid dishwashing soap with three parts water. 
2.    Make sure control knobs are in the “OFF” position. 
3.    Spray some solution on the connection points of the natural gas hose. 
4.    Inspect the solution at the connections for bubbles. If no bubbles appear, the connection is secure. 
5.    If bubbles appear, you have a leak. Go to step 6. 
6.    Disconnect the natural gas hose from the valve and reconnect. Make sure the connection is secured. 
7.    Retest with solution. 
8.    If you continue to see bubbles, replace the quick release connector or/and natural gas hose. 

 

Lighting Your Grill 

DANGER:

 

Failure to open lid while igniting the grill’s burners or not waiting five minutes to allow gas to clear if the grill does not light, may 
result in an explosion, which could cause serious bodily injury or death. 

 

Summary of Contents for SSS3416TBSN




















Reviews: