background image

REMOTE TURN ON OPTIONS

OPTION ONE:

When you are using this option with all amplified Bass Tubes

®

models:

 

For the most versatility the Orange Remote Turn On Wire

should be connected to the source unit's "Accessory", "Auto-Antenna"

or "Remote" lead -- any of which will supply 12 Volts positive when

the source is turned on.

OPTION TWO:

When you are using this option

If the source does not have an Auto-Antenna lead (or if the Auto-

Antenna goes down during tape operation), you can connect the

Amplified Bazookas' Remote Turn On Wire to an accessory or ignition

point at the vehicle fuse block. In this configuration, the Amplified

Bazooka subwoofer will be on whenever the ignition is on. This

method may allow noise or turn-on-and-off transients to become

amplified when the source unit is not in use, and therefore is a less

desirable than option one. Locate the Auto/Off Jumper Loop located

on the wiring harness; SAS ships the Amplified Bazooka subwoofer

with this Jumper in the ON Position. The Quick Disconnect YELLOW

On/Off Jumper Loop must be plugged into the harness.

Low-Level Inputs:

If your source unit only has low-level RCA phono jack output, use only

the low-level inputs of the Amplified Bazooka. Connect the low-level

RCA phono jack inputs of the Amplified Bazooka subwoofer to the

source with a shielded RCA patch cord. To avoid possible noise

problems, be sure to run the patch cord away from all power wires

and factory wire harnesses. When using the low-level inputs DO NOT

make any connections to the Green and Gray high-level input wires

of the Amplified Bazooka subwoofer and make sure these wires are

insulated to avoid the possibility of a short circuit.

POWER WIRE

The power wire must be fused and connected directly to the positive

terminal of the battery to provide a power source with a low voltage

drop and low noise. Do not make the power connection at the fuse

block or any point other than the battery. Improper power sources

can reduce output and cause distortion.

The fuse holder should be connected to the battery's positive terminal.

The fuse is designed to prevent fire or damage to your car, should

the battery wire short to ground. Wait to insert the fuse into its holder

until all wire connections have been made.

If it is necessary to lengthen the battery wire, add the required length

between the amplifier and the fuse holder, not the fuse holder and

the battery. If you need to extend t  he battery wire, use 16 gauge

or larger for all A100, and 12 gauge or larger for all A200 models. It

is best to use as short a wire as possible. Be sure you DO NOT run the

power wire next to the input cables of the amplifier this will induce

noise. Avoid running the power wire near the radio's antenna or

power leads, or near sensitive equipment or harnesses. The power

wire carries substantial currents and could induce noise.

GROUND WIRE

The ground wire must be connected directly to the vehicle chassis

near the amplifier. We do not recommend extending the ground wire

in any installation, as this can cause unwanted ground loops.

The ground point in the car should be a piece of chassis metal that

is part of or welded to the main body of the vehicle. Painted surfaces

should be scraped or sanded clean to expose the bare metal before

the ground lug is bolted down. (Cover the bare metal area with paint

or grease after you finish mounting the ground wire to prevent rust.)

ENGLISH

ENGLISH

11

12

Summary of Contents for BTA850FH











Reviews: