Bayside Furnishings Ario 3-in-1 ARI3N1CGT Manual Download Page 24

Page: 24 / 27

Model # ARI3N1CGT

Bayside Furnishings

Page 24

Factory No. 10944

Assembly Instruction for installing the Mounting Frame onto BRICK, SOLID

CONCRETE OR CONCRETE BLOCK WALLS

NOTE

: If you are mounting your TV to a wall with wooden studs, skip this section.

This

assembly

requires an

electric drill and level (not included).

38. Begin by placing the Mounting Frame (K) level against the wall where you intend to mount the

TV. Using the Mounting Frame (K) as a template, mark 4 drill points with a pencil.

39. With an electric drill (not included) on its low setting, drill 7/16 inch diameter holes to at least

2½ inch (63.5 mm) deep. Insert the Concrete Anchors (7) into the pre-drilled holes so that they
are flush with the wall.

40. Place the Mounting Frame (K) level in the desired position against the wall. Secure the

Mounting Frame (K) to wall with the Lag Bolts (8) and the Washers (9) at the drill points.
Tighten the bolts firmly, but be careful not to over tighten.

Concrete Anchors should only be used for masonry mounting.

NEVER use the wall anchors to mount the unit to drywall.

Maximum weight 135 lb. (61.2 kg)

Summary of Contents for Ario 3-in-1 ARI3N1CGT




























Search results

Summary of Contents for Ario 3-in-1 ARI3N1CGT

Reviews:

Related manuals for Ario 3-in-1 ARI3N1CGT

Brands by name

Popular brands

Bayside Furnishings Ario 3-in-1 ARI3N1CGT, Manual

Search results

Summary of Contents for Ario 3-in-1 ARI3N1CGT

Reviews:

Related manuals for Ario 3-in-1 ARI3N1CGT

Brands by name

Popular brands