Baxi COMPACT E, Instruction Manual For Users And Fitters

Page: 9 / 40

31
I
N
S
T
A
L
L
E
R
S
e
c
t
i
o
n
(
e
n
)
7733595 (01-05/19)
10. INSTALLING THE FLUE
7KH ERLOHU LV HDV\ DQG ÀH[LEOH WR LQVWDOO WKDQNV WR WKH H[WHQVLYH UDQJH RI DYDLODEOH
DFFHVVRULHV DV GHVFULEHG EHORZ7KH ERLOHU KDV EHHQ GHVLJQHG IRU FRQQHFWLRQ WR D
YHUWLFDORUKRUL]RQWDOFRD[LDOÀXHDLUGXFW7KHERLOHUFDQDOVREHXVHGZLWKVHSDUDWH
ducts using the accessory splitting kit.
WARNINGS
C13, C33
7KHWHUPLQDOVIRUVHSDUDWHÀXHVPXVWEH¿WWHGLQVLGHDFPVTXDUH'HWDLOHG
LQVWUXFWLRQVDUHSURYLGHGZLWKWKHLQGLYLGXDODFFHVVRULHV
C53
'RQRW¿WWKHÀXHDQGDLUGXFWWHUPLQDOVRQRSSRVLWHZDOOVRIWKHEXLOGLQJ
C63 The pressure drop of the ducts must not exceed 100 Pa
7KHGXFWVPXVWEHFHUWL¿HG
IRUWKLVVSHFL¿FXVHDQGIRUDWHPSHUDWXUHLQH[FHVVRIƒ&7KHÀXHWHUPLQDOPXVWEH
FHUWL¿HGWR(1
C43, C83
7KHÀXHWHUPLQDORUÀXHGXFWPXVWEHVXLWDEOHIRUWKHSXUSRVH
For optimal installation, the accessories supplied by the manufacturer should
be used.
7RRSWLPLVHRSHUDWLQJVDIHW\PDNHVXUHWKHÀXHGXFWVDUH¿UPO\¿[HGWRWKHZDOOZLWKVXLWDEOHEUDFNHWV7KHEUDFNHWVPXVWEH
positioned over the joints at a distance of approximately 1 metre from one another.
SOME OUTLET DUCT INSTALLATION EXAMPLES AND THEIR RELATIVE MAXIMUM LENGTHS ARE SHOWN IN ANNEX
"SECTION" D AT THE END OF THIS MANUAL.
10.1 CONCENTRIC DUCTS
7KLVW\SHRIGXFWLVXVHGWRGLVFKDUJHH[KDXVWIXPHVDQGGUDZ
FRPEXVWLRQDLUERWKRXWVLGHWKHEXLOGLQJDQGLID/$6ÀXHLV¿WWHG
7KHƒFRD[LDOEHQGDOORZVWKHERLOHUWREHFRQQHFWHGWRDÀXH
DLUGXFWLQDQ\GLUHFWLRQDVLWFDQEHURWDWHGE\ƒ,WFDQDOVR
EHXVHGDVDVXSSOHPHQWDU\FXUYHFRPELQHGZLWKDFRD[LDOGXFW
RUDƒFXUYH
,I IXPHV DUH GLVFKDUJHG RXWVLGH WKH EXLOGLQJ WKH ÀXHDLU GXFW
PXVWSURWUXGHDWOHDVWPPIURPWKHZDOOWRDOORZDQDOXPLQLXP
ZHDWKHULQJ VXUURXQG WR EH ¿WWHG DQG VHDOHG WR DYRLG ZDWHU
LQ¿OWUDWLRQV
•
A 90° bend reduces the total duct length by 1 metre.
• A 45° bend reduces the total duct length by 0.5 metres.
•
7KH¿UVWƒEHQGLVQRWLQFOXGHGZKHQFDOFXODWLQJWKHPD[LPXPDYDLODEOHOHQJWK
6HFXUHWKHLQWDNHSLSHVZLWKWZRJDOYDQLVHGVFUHZVZLWKDGLDPHWHURIPPDQGDPD[LPXPOHQJWKRIPP
%HIRUHVHFXULQJWKHVFUHZVPDNHVXUHWKDWDWOHDVWPPRIWKHSLSHLVLQVHUWHGLQWRWKHJDVNHWVHHWKH¿JXUHVLQDQQH[
"SECTION" D at the end of this manual).
Make sure there is a minimum downward slope of 5 cm per metre of duct towards the boiler.
10.2 SEPARATE DUCTS
)RU VSHFLDO LQVWDOODWLRQV RI WKH IXPHV LQOHWRXWOHW GXFWV WKH
single splitting kit ( C ), supplied as an accessory, can be used.
This accessory, in fact, can be used to move the inlet and outlet
in any direction. This type of installation makes it possible to
discharge exhaust fumes both outside the building and into
VLQJOHÀXHGXFWV&RPEXUHQWDLUFDQEHGUDZQLQDWDGLႇHUHQW
ORFDWLRQIURPWKDWRIWKHÀXHWHUPLQDO7KHVSOLWWLQJNLWLV¿[HG
WRWKHERLOHUWXUUHWPPDQGDOORZVWKHFRPEXUHQWDLU
DQG RXWOHW IXPHV WR HQWHUOHDYH WKH WZR VHSDUDWH GXFWV
mm). For further information, read the assembly instructions
VXSSOLHGZLWKWKHDFFHVVRU\
7KH ƒ EHQG LV XVHG WR FRQQHFW WKH ERLOHU WR WKH LQOHW DQG
outlet ducts, adapting them to various requirements. It can
DOVREHXVHGDVDVXSSOHPHQWDU\FXUYHFRPELQHGZLWKDGXFW
RUDƒEHQG
• A 90° bend reduces the total duct length by 0.5 metres.
• A 45° bend reduces the total duct length by 0.25 metres.
•
7KH¿UVWƒEHQGLVQRWLQFOXGHGZKHQFDOFXODWLQJWKHPD[LPXPDYDLODEOHOHQJWK